Technical Data - EINHELL TC-SS 405 E Manual De Instrucciones

Ocultar thumbs Ver también para TC-SS 405 E:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 87
All manuals and user guides at all-guides.com
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
The equipment is to be operated only with suita-
ble saw blades. It is prohibited to use any type of
cutting-off wheel. To use the equipment properly
you must also observe the safety regulations, the
assembly instructions and the operating instruc-
tions to be found in this manual.
All persons who use and service the equipment
have to be acquainted with this manual and must
be informed about the machine's potential ha-
zards.
It is also imperative to observe the accident pre-
vention regulations in force in your area.
The same applies for the general rules of health
and safety at work.
The manufacturer will not be liable for any chan-
ges made to the machine nor for any damage
resulting from such changes.
Even when the equipment is used as prescribed
it is still impossible to eliminate certain residual
risk factors. The following hazards may arise in
connection with the machine's construction and
design:
Harmful emissions of wood dust when used
in closed rooms.
Contact with the blade in the uncovered cut-
ting zone.
Injuries (cuts) when changing the blade.
Crushed fingers.
Kickback.
Tilting of the workpiece due to inadequate
support.
Touching the blade.
This appliance is not intended for use by persons
(including children) with reduced physical, sen-
sory or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
Anl_TC_SS_405_E_SPK9.indb 17
Anl_TC_SS_405_E_SPK9.indb 17
GB

4. Technical data

Mains voltage: ................................. 230 V ~ 50Hz
Power consumption: .................................. 120 W
Operating mode: ................................. S2 10 min
Idle speed n
: ................................400-1600 min
0
Stroke: ...................................................... 14 mm
Tilting range of table: .............. 0° to 45° to the left
Table size: ...................................... 408 x 250 mm
Saw blade length: ................................... 127 mm
Throat: .................................................... 406 mm
Max. cutting height at 90°: ......................... 52 mm
Max. cutting height at 45°: ........................ 20 mm
Weight: ........................................................13 kg
Load factor:
A load factor of 10 min (intermittent periodic
duty) means that you may operate the motor
continuously at its nominal power level (120W)
for no longer than the time stipulated on the spe-
cifi cations label (10 min). If you fail to observe
this time limit the motor will overheat. During the
OFF period the motor will cool again to its starting
temperature.
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
L
sound pressure level ..................... 90,1 dB(A)
pA
K
uncertainty ............................................. 3 dB
pA
L
sound power level ..................... 103,1 dB(A)
WA
K
uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
- 17 -
-1
22.02.2019 06:20:47
22.02.2019 06:20:47

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

43.090.40

Tabla de contenido