Nice smu Instrucciones Y Advertencias Para El Usuario página 3

Table "A" Entering a new transmitter in the receiver's memory
This function allows you to enter a new transmitter in the radio receiver
1. Press key "TX+"
2. Entry mode "A A L L L L " (Mode 1) will appear on the display.
To select mode 2, press key "TX+" a few times until the desired output is displayed.
To return to Mode 1 press key "TX+" until "A A L L L L " appears on the display.
3. A few seconds after key "TX+" was last pressed, radio transmission symbol ". .
will appear on the display.
4. While symbol ". .
transmitter to be memorized.
5. When it receives the code, SMU will enter it in the receiver's memory and the position
where it has been entered will be shown on the display for 10 seconds.
Note: The position where the transmitter has been entered should be written down in a list; this list can be used later if you need to delete
a transmitter code and the transmitter is not available.
Table "B" Searching for a transmitter in the receiver's memory
This function allows you to view the code's position in the memory and its entry mode.
1. Press key "?TX"
2. Radio transmission symbol ". .
3. While the symbol is being displayed, press the desired key on the transmitter to be
searched for.
4. When you have found the code in the receiver's memory, SMU will show the code's
position in the memory and its entry mode by turns.
After 4 times only the position in the memory will remain displayed.
Note: If a code is not found, SMU will show the last position occupied by the code, then the symbol "n n o o - - P P " will appear.
Table "C" Deleting a code from the receiver's memory without the transmitter
This function allows you to delete a code from the receiver's memory when you know its memorized position.
1. Press arrow " " or " " to select the position to be deleted.
2. Press key "TX-".
3. "P P r r E E S S " will appear on the display; press key "TX-" once again to confirm the deletion.
4. "d d e e L L " will appear briefly on the display, confirming the deletion, then the position where
the code has been deleted will be shown.
Table "D" Deleting a code from the receiver's memory using the transmitter
This function allows you to delete a position from the receiver's memory using the transmitter to be deleted.
1. Press key "?TX"
2. Radio transmission symbol ". .
3. While the symbol is being displayed, transmit by pressing the desired key on the transmitter
to be searched for.
4. When you have found the code in the receiver's memory, SMU will show the code's
position in the memory and its entry mode by turns. After 4 times only the position in the
memory will remain displayed.
5. Press key "TX-" to delete the code.
6. "P P r r E E S S " will appear on the display; press key "TX-" once again to confirm the deletion.
7. If the deletion operation has been successfully completed, the position where the code has
been deleted will be displayed.
] ] " is being displayed, transmit by pressing the desired key on the
] ]
] ] " will appear on the display.
] ]
] ] " will appear on the display.
] ]
Example
TX +
A A L L L L
O O u u t t 1 1
O O u u t t 3 3
A A L L L L
] ] "
] ]
. . ] ]
] ]
0 0 0 0 2 2 5 5
Example
?TX
. . ] ]
] ]
0 0 0 0 2 2 5 5
O O u u t t 1 1
Example
or
TX -
P P r r E E S S
TX -
d d e e L L
0 0 0 0 2 2 5 5
Example
?TX
. . ] ]
] ]
0 0 0 0 2 2 5 5
O O u u t t 1 1
TX -
P P r r E E S S
TX -
0 0 0 0 2 2 5 5
GB
O O u u t t 2 2
O O u u t t 4 4
0 0 0 0 2 2 5 5
3