Black and Decker BDPS200 Manual De Instrucciones página 28

28 • ENGLISH
The liquid being sprayed may need to be thinned (diluted)
before starting. When thin- ning, use the proper liquid
thinner recom- mended on the container by the material
manufacturer and the proper dilution rate.
Warning!: Do not use materials with a flashpoint higher
than 60°C (140°F) .
A 2- 3/4 quart mixing bucket is provided to use
when transferring spray material from the original
container into the bucket for thinning and
measuring purposes (Fig. E).
f If material needs thinning, add the appropriate liquid
thinning material recommended by the manufacturer
(Fig. E1).
f The quick clean fill cup has a measurement of 2.5
ozs. This can be used as a quick measurement when
thinning to 5% in the side fill canister.
f It is possible to spray latex paint with this unit,
howeer, the required thinning may exceed material
manufacturer's recommendation. The operator should
consider the type of application and final location of
the project when spraying.
COMMONDILUTION RATES ON PAINT CAN
MANUFACTURERS
SUGGESTED
1/2 pint
5%
10%
PREPARATION TIPS
f With any spraying job you should always ensure that
you have properly prepared the surface to get the best
finish. That is, that all surfaces are free from dust,
dirt, rust and grease. Lightly pressure wash decks or
exterior surfaces and ensure that they are dry before
spraying.
f It is recommended that you mask all edges and other
areas and use drop cloths to protect your floors and
anything else in the spraying area that you wish to
remain untouched.
f Skin that forms on the top of paint can clog the
sprayer. Remove skin before mixing. Older material
may need to be strained with a funnel with a filter
attached or through hosiery to remove any impurities
that could clog system.
f Before starting have gloves, paper towels, rags etc.
available for unexpected spills.
FILLING THE CANISTER - (FIG. F)
f Check to make sure that the canister is completely
screwed onto the sprayer.
OUNCES PER GALLON
8 ounces
6-1/2 ounces
13 ounces
f Lay the sprayer on its side with the canister side lid
facing up.
f Unscrew the lid on the side of the canister.
f Pour the properly thinned and strained material to be
sprayed into the side fill canister (Fig. F).
Tip: Use the mixing bucket provided to pour
material from the original material container into
the side fill canister.
f Clean any residual liquid from the threads or sides of
the canister and sprayer.
f Starting the threads evenly, screw the lid completely
onto the side fill canister. Check the lid to make sure it
is threaded on squarely and completely before picking
up the sprayer.
FLOW CONTROL SETTINGS
FLOW CONTROL KNOB - (FIG. G)
The flow control knob regulates the amount of liquid that
can be sprayed.
f Select low (1), medium (5) or high (9) on the flow
control knob.
Tip: Always test the spray pattern on scrap cardboard
or similar material first. Begin with flow control
knob on the highest flow setting. Heavier, thicker
materials should be sprayed on the higher setting
closer to #9. Thinner materials should be sprayed on
the lower setting closer to #1.
OPERATION
ON / OFF TRIGGER - (FIG. H)
The sprayer is turned on and off by the trigger.
f To turn the sprayer on, squeeze the trigger.
f To turn the sprayer off, release the trigger.
Warning!: Risk of injury. Never point the sprayer at
any part of the body. Never pull the trigger while adjusting
the spray setting.
DEVELOPING THE PROPER
SPRAYING TECHNIQUE
f Practice spraying on a piece of scrap material such
as cardboard to test your spray pattern and become
familiar with the speed settings flow control features
of the sprayer.
f Ensure surface to be sprayed is free of dust, dirt, and
grease.
f Ensure spray area is clean and free of dust that could
be blown onto newly sprayed surfaces.
f Cover any areas not intended to be sprayed.