Maintenance Procedures - Legacy Levelwind Serie Guía De Componentes Y Servicio Técnico

SEVEN POSITION LOCKING BRACE
LEVELWIND retractable hose reels can swing freely on bracket or can
be locked in one of seven positions, allowing for specific mounting
requirements.
S S t t a a n n d d a a r r d d b b r r a a c c k k e e t t
1) Remove bracket rod from reel. (SEE FIGURE 5A)
2) Place seven position locking brace over bracket so that bracket
rod holes are aligned. Replace bracket rod so that brace, reel &
bracket are attached. (SEE FIGURE 5B)
3) Rotate bracket so that it is at desired angle & lock into place with
fastener. (SEE FIGURE 5B)

Maintenance Procedures

TENSION ADJUSTMENT:
This reel is preloaded with spring tension that is set at the factory. If the reel becomes completely un-tensioned, please identify your hose reel model
number referenced in the Factory Preset Tensioning Table to find out how many turns are needed for proper tensioning. If a heavy air tool is attached
to the end of the hose, you may need to add tension to overcome the weight of this tool. DO NOT EXCEED one full turn past the number of turns
listed in the Factory Preset Tensioning Chart below.
TOOLS REQUIRED:
Phillips Screw Driver
¾" Socket Wrench
1) Lay reel on its side. ( SEE FIGURE 7 )
2) Place wrench on hub fitting plate nut. HOLD WRENCH FIRMLY.
3) Unscrew hub. DO NOT REMOVE SIDEPLATE.
4) Turn wrench either ½ turn or no more than one full turn. Turn
clock wise to increase tension. Turn counterclockwise to
decrease tension.
5) Replace hub plate screws and tighten. Return reel to mounting
bracket.
HOSE REPLACEMENT:
To ensure proper performance, please consult the Hose
Replacement Kit table for the appropriate part number
to order. Call 1(800) 645-8258 to order kit.
R R e e p p l l a a c c e e m m e e n n t t H H o o s s e e K K i i t t s s
1) Pull entire length of hose out of reel.
( SEE FIGURE 8 )
2) While entire length of hose is out of the reel, place
long screw driver ( 3/8" in diameter ) all the way
though the the hole located at the back portion of
reel. This eliminates any chance for the reel to
retract while replacing hose.
S S i i d d e e p p l l a a t t e e r r e e m m o o v v a a l l
3) Locate inlet sideplate. Remove four fasteners (SEE FIGURE 9 ). While placing fingers on grooves located on the top and bottom of sideplate,
depress locking tabs at the same time with thumbs (SEE FIGURE 10). Rotate side plate either way until sideplate unlocks. Remove sideplate.
4) Remove wear plate (SEE FIGURE 11). Unscrew two fasteners on wear ring and remove wear ring (SEE FIGURE 12).
Fig. 9
Screws
Screws
Inlet Side Plate Front
Back
Fig.7
Fig. 8
2
Fig. 10
Fig. 5a
Fig. 5b
Decrease
Increase
Hub
Screw
Screw
1
M M o o d d e e l l # #
RP005005
RP005005-EU
RP005006
RP005006-EU
RP005008
RP0050058-EU
RP005035
RP005035-EU
RP005047
RP005049
Fig. 11
Wear Plate
Page 2
Fig. 6
Optional Bench/High Wall
Mounting Bracket
Factory Preset Tensioning Table
M M o o d d e e l l # #
L8305
L8305-EU
L8306
L8306-EU
L8310
L8310-EU
L8335
L8335-EU
L8346
L8347
L8349
Replacement Hose Kits
D D e e s s c c r r i i p p t t i i o o n n
Replacement Hose Assembly for L8305
Replacement Hose Assembly for L8305-EU
Replacement Hose Assembly for L8306
Replacement Hose Assembly for L8306-EU
Replacement Hose Assembly for L8310
Replacement Hose Assembly for L8310-EU
Replacement Hose Assembly for L8335
Replacement Hose Assembly for L8335-EU
Replacement Hose Assembly for L8347
Replacement Hose Assembly for L8349, L8346
Fig. 12
Wear Ring
Screws
(see figure 6)
# # o o f f T T u u r r n n s s
3
3
5
5
4
4
4
4
4
4
4
Screws