Technical Assistance - Legacy Levelwind Serie Guía De Componentes Y Servicio Técnico

5) Pull swivel assembly firmly from hose spool
( SEE FIGURE 13 and 14 ).
6) Unscrew Hose Clamp and pull hose off hose barb on swivel.
(SEE FIGURE 15)
7) Pull remaining length of hose out reel opening located at the reel
front.
8) Take replacement hose through opening located at the front of reel.
Thread hose through hose leveling mechanism. (SEE FIGURE 16)
9) Insert hose through the center of the hose spool. Four openings are
referenced with the following hose I.D. dimensions located at the
center of hose spool: 3/8", 1/2",5/8" & 3/4". Locate the appropriate
hose I.D. and pull through that opening. (SEE FIGURE 17) Pull
enough hose to allow the hose to connect to appropriate hose barb
on swivel.
10) Replace hose onto hose barb, tighten hose clamp onto hose & place
swivel into hose spool housing. Make sure that drive tabs for spool
located on swivel are accepted by tab receivers in hose spool. (SEE
FIGURE 18)
11) Replace wear ring and fasten with wear ring screws. Replace wear
plate so that the swivel drive tabs insert into wear plate tab receivers.
(SEE FIGURE 19)
12) Replace sideplate so that the plate snaps flush to side of reel. Turn
sideplate until locking tabs connect to sideplate.
13) Turn swivel so that fastener holes of swivel and sideplate align.
Replace the four sideplate fasteners and tighten.
14) Remove Screw driver.
15) Retract hose back into reel.
Swivel Seal Kits
P P a a r r t t # # D D e e s s c c r r i i p p t t i i o o n n
RP005007-38 Seal Replacement kit for reel model L8305, L8305-EU, L8306
L8306-EU, L8310. L8310-EU
RP005007-12 Seal Replacement kit for reel model L8335, L8335-EU
RP005007-58 Seal Replacement kit for reel model L8346, L8347 & L8349
SWIVEL SEAL REPLACEMENT
IMPORTANT: To ensure proper performance, please refer to the Swivel
Seal Replacement Kit table to order the correct part number. Call 1(800)
645-8258 to order kit.
1) Repeat steps 1- 6 in the HOSE REPLACEMENT procedure.
2) Place hose onto hose barb of new swivel body. Tighten hose clamp
onto hose & place swivel into hose spool housing. Make sure that
drive tabs for spool located on swivel are accepted by tab receivers in
hose spool (SEE FIGURE 18).
3) Replace wear ring and fasten with wear ring screws. Replace wear
plate so that the swivel drive tabs insert into wear plate tab receivers.
(SEE FIGURE 19)
4) Replace sideplate so that the plate snaps flush to side of reel. Turn
sideplate until locking tabs connect to sideplate.
5) Turn swivel so that fastener holes of swivel and sideplate align.
Replace the four sideplate fasteners and tighten.
6) Remove Screw driver.
7) Retract hose back into reel.
Troubleshooting
1 1 ) ) H H O O S S E E W W I I L L L L N N O O T T R R E E T T R R A A C C T T
1a. Pull on hose, push latching switch to FreeRun mode. Retract hose into reel.
1b. Spring is broken. Call service center.
2 2 ) ) H H O O S S E E W W I I L L L L N N O O T T F F U U L L L L Y Y R R E E T T R R A A C C T T
2a. Spring tension too light?
2b. Replacement hose too heavy?
3 3 ) ) R R E E E E L L W W I I L L L L N N O O T T L L A A T T C C H H
3a. Are you releasing hose too quickly?
3b. Broken latching pawl or mode switch?
4 4 ) ) R R E E E E L L L L E E A A K K S S
4a. Damaged hose?
4b. Loose fittings?
4c. Worn swivel seals?
Fig. 13
Swivel Body
Hose
Hose Spool
Fig. 15
Hose
Hose Barb
Hose Clamp
Fig. 17

TECHNICAL ASSISTANCE:

Call 800-645-8258 if you have any questions
regarding the installation or operation of this
reel.
Page 3
Fig. 14
Fig. 16
Swivel
Assembly
Hose Leveling
Mechanism
Fig. 18
Hose Spool
Tab Receivers
Fig. 19
Swivel
Drive Tabs
Wear Plate
Tab Receivers
Reel
Opening
Swivel
Drive Tabs