Additional Safety Rules For Impact Drivers; Additional Instructions For Work With The Charger - Redstone RS 10.8Li CC Instrucciones De Uso Originales

5. SERVICE
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Additional safety rules
for impact drivers
▪ Be aware that this tool is always in operating condi-
tion, because it does not have to be plugged into an
electrical outlet. Always set the trigger switch to the
locked OFF position when installing or removing the
battery pack.
▪ Wear ear protectors when impact drilling. Expo-
sure to noise can cause hearing loss.
▪ Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or
its own cord. Cutting accessory contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
▪ The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual
will be considered a case of misuse. The user and not
the manufacturer shall be liable for any damage or in-
jury resulting from such cases of misuse.
▪ To use this tool properly, you must observe the safety
regulations, the assembly instructions and the oper-
ating instructions to be found in this Manual. All per-
sons who use and service the machine have to be
acquainted with this Manual and must be informed
about its potential hazards. Children and frail people
must not use this tool. Children should be supervised
at all times if they are in the area in which the tool is
being used. It is also imperative that you observe the
accident prevention regulations in force in your area.
The same applies for general rules of occupational
health and safety.
▪ The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from
such changes.
▪ Even when the tool is used as prescribed it is not pos-
sible to eliminate all residual risk factors. The following
hazards may arise in connection with the tool's con-
struction and design:
▪ Damage to hearing if effective ear defenders are not
worn.
Additional instructions
for work with the charger
▪ Before using the charger, read all the instructions and
cautionary markings on the charger and battery pack
as well as the instructions on using the battery pack.
▪ Only charge your batteries indoors as the charger is
designed for indoor use only.
14
EN
WARNING: If the battery pack is cracked or
damaged in any other way, do not insert it in the char-
ger. There is a danger of electric shock.
WARNING: Do not allow any liquid to come
into contact with the charger. There is a danger of elec-
tric shock.
▪ The charger is not intended for any use other than
charging the exact type of REDSTONE rechargeable
battery pack as supplied with the charger. Any other
use may result in the risk of fire or electric shock.
▪ The charger and battery packs supplied with it are
specifically designed to work together. Do not attempt
to charge the battery pack with any other charger than
the one supplied.
▪ Do not place any object on top of the charger as it
could cause overheating. Do not place the charger
near any heat source.
▪ Do not pull on the lead of the charger to disconnect it
from the power source.
▪ Make sure that the charger cable is positioned where
it will not be stepped on, tripped over or otherwise
subjected to damage or stress.
▪ Do not use an extension cord unless it is absolutely
necessary. The use of an improper extension cord
could cause the risk of fire or electric shock.
▪ Do not use the charger if it has been subjected to a
heavy knock, dropped or otherwise damaged in any
way. Do not operate charger with damaged cord or
plug - have them replaced immediately. Take the
charger to an authorised service centre for a check
or repair.
▪ If the replacement of the supply cord is necessary, this
has to be done by the manufacturer or his agent in
order to avoid a safety hazard.
▪ Do not disassemble the charger. Take it to an author-
ised service centre when service or repair is required.
Incorrect re-assembly may result in the risk of fire or
electric shock.
▪ To reduce the risk of an electric shock, unplug the
charger from the power supply before attempting to
clean it. Removing the battery pack alone does not
reduce the risk.
▪ Never attempt to connect two chargers together.
▪ Do not store or use the tool and battery pack in lo-
cations where the temperature may reach or exceed
40°C such as alongside sheds, trailers or metal struc-
tures during summer.
▪ The charger is designed for use from a standard
household electrical supply (230–240 V). Do not at-
tempt to connect the charger to a supply with a dif-
ferent voltage.
▪ If you wish to charge a second battery pack, unplug
the charger from the mains supply and leave it for at
least 15 minutes. After this time you can charge a sec-
ond battery pack.
▪ Under certain conditions, with the charger plugged in
to the power supply, the exposed charging contacts
inside the charger can be shorted by foreign material.
RS 10.8Li CC