Know Your Product; Operation - Redstone RS 10.8Li CC Instrucciones De Uso Originales

Atornillador de impacto a batería
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 30
does not indicate a problem.
▪ After completion of charging the red LED ceases to
glow and the green LED lights up.
▪ The charger features thermal overload protection for
the battery. Nevertheless we recommend withdraw-
ing the battery from the charger upon expiring of the
charging time. You may use additionally an electric
timer in order to control the charging time.
TO OBTAIN THE BEST LIFE FOR THE BATTERY
▪ When battery is not in use, keep it away from other
metal objects like paper clips, coins, keys, nails,
screws, or other small metal objects that can make
a connection from one terminal to another. Shorting
the battery terminals together may cause fire or ex-
plosion.
▪ Always unplug the charger when not in use and store
in a dry secure place.
▪ Do not charge battery packs and do not store the
charger in premises where the temperature may drop
under 0ºC or exceed +40ºC.
BATTERY STATE INDICATION
The battery state during operation can be checked by
the LED display (4). To actuate the indicator press the
ON/OFF trigger switch (5).
3 = Battery 100% - 60% charged.
2 = Battery 60% - 30% charged.
1 = Battery < 30% charged. It is necessary to recharge
the battery.
The direction of decreasing the charge level indicated by
the LEDs is marked on the housing of the power tool.

Know your product

Before using the power tool, familiarize yourself with all
operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
1. Locking sleeve
2. Bit holder
3. LED work light
4. LED battery indicator
5. ON/OFF trigger switch
6. Forward reverse switch
7. Battery release buttons
8. Battery
9. LED charge state indicator
10. Charger

Operation

LED WORK AREA LIGHT
The machine is equipped with LED light (3) to illuminate
the work area and improve visibility when drilling in areas
with insufficient light. The LED light is on until the ON/
OFF switch (5) is pressed.
16
EN
REVERSING
The extreme position of lever (6) to the right (viewed from
the rear) is equivalent to anti-clockwise rotation, the ex-
treme position to the left - to clockwise rotation. When
the ON/OFF switch (5) is depressed lever (6) can not be
actuated. (Fig. 1)
WARNING: Reversing can be performed only
when the spindle is not rotating!
Drilling and tightening screws are performed with lever
in extreme position to the left. Removal of screws is per-
formed with lever in extreme position to the right.
SWITCHING ON - SWITCHING OFF
Switching on: press ON/OFF switch (5).
Switching off: release ON/OFF switch (5).
The power tool is equipped with a brake. The spindle
stops rotating immediately after releasing the switch le-
ver.
SMOOTH ELECTRONIC RPM CONTROL
Light pressure on ON/OFF trigger switch (5) results in
low rotation speed, further pressing the switch results in
smooth increase of the rpm to maximum upon reaching
the extreme position.
WARNING: The continuous operation of the
electronic control may overload or damage the regu-
lator.
OPERATING THE TOOL
Impact operation starts automatically when the load ex-
ceeds certain level. Pushing the trigger switch at no load
will result only in change of speed.
The fastening torque depends on the duration of impact
operation. Generally, maximum torque is achieved after
6 to 10 seconds of impact operation. Further operation
will result only in slight torque increase. Prolonged im-
pact operation may cause motor damage or burning.
The torque depends on the length, grade and diameter
of the screw. It depends also on the strength of material
to be fastened (wood, metal, etc.) and the type of washer
used. Operate the tool after calculating the appropriate
impact operation time by performing a trial fastening
and measuring the actually achieved torque by a torque
wrench.
The torque depends on the length, grade and diameter
of the screw. It depends also on the rigidness of material
to be fastened (wood, metal, etc.) and the type of washer
used. Operate the tool after calculating the appropriate
impact operation time by performing a trial fastening
and measuring the actually achieved torque by a torque
wrench.
WARNING: Power tool with a faulty switch is
dangerous and shall be repaired before use.
RS 10.8Li CC

Publicidad

Tabla de contenido
loading

Tabla de contenido