Schlage ND Serie Instrucciones De Instalación página 2

KEYED LEVERS / TIMING
IMPORTANT: DO NOT insert key in outside cylinder (if applicable) before or during these steps. FAILURE TO PROPERLY TIME THE LOCK WILL RESULT IN IMPROPER FUNCTION, AND CAN CAUSE DAMAGE TO THE LOCK.
ND70 and ND73 ONLY
a
STANDARD CYLINDER: IC CYLINDER:
Install chassis only. Install lock except for outside
IC and driver.
ND60, ND66, ND72, ND75, ND93, ND94, ND95 and ND97 ONLY
a
STANDARD CYLINDER:
Install lock except for inside lever *
* ND72 ONLY: Install chassis only. Both inside
and outside cams require timing.
Remove a Keyed Lever
a
To remove a keyed lever, rotate key 90°.
90°
DOOR THICKNESS ADJUSTMENT
For 1³⁄₄" thick doors, NO ADJUSTMENT
IS REQUIRED.
For 1³⁄₈" thick doors, install the Optional
Spacers (see steps 2 and 4). No further
adjustment is required.
For 1⁵⁄₈", 2" or 2¹⁄₈" doors, complete the
following steps.
b
Rotate key cam counterclockwise until it stops. Then rotate
clockwise to the position as shown below.
STANDARD CYLINDER IC CYLINDER
IC CYLINDER:
Install lock except for inside IC and driver *
*ND72 ONLY: Install lock except for inside and
outside IC and driver. Both inside and outside
cams require timing.
b
Insert pin wrench and push against lever catch.
Pull off the lever.
a b
Remove adjustment plate and door Reinsert door thickness insert with
thickness insert.
correct dimension visible.
Door thickness
1⁵⁄₈"
insert
2"
2¹⁄₈"
c
STANDARD CYLINDER:
Install the outside lever.
Then, continue with Step 4.
b
Rotate key cam clockwise to the correct position as shown below.*
*ND72 ONLY: Rquired on inside and outside cams.
IC Cylinder ND66 Standard Cylinder
Standard Cylinder
TROUBLESHOOTING–If levers do not function properly, follow these steps:
a b
Remove lever as Rotate key 180° and reinstall lever.
shown at left.
180°
If door thickness insert is missing, use marks
on chassis:
1³⁄₈" Align adjustment plate with 1³⁄₄" mark.
Use optional spacers. (For ND85 rotate additional half
turn CCW.)
1⁵⁄₈" Tighten adjustment plate to bottom, then rotate a
half turn CCW.
1³⁄₄" Align adjustment plate with 1³⁄₄" mark. (For ND85
2" 1³⁄₄"
rotate an additional half turn CCW.)
2" Align adjustment plate with 2" mark.
2¹⁄₈" Align adjustment plate with 2" mark, then rotate an
additional full turn CCW.
CCW = counterclockwise
IC CYLINDER: Turn the key 15° and hold.
Insert driver.
Install the cylinder.
Align cylinder tailpiece blade and keyway.
Then, continue with Step 4
FSIC SFIC
Keyway
Tailpiece
blade
FSIC shown
c
Follow step C as shown above.
Then, continue with Step 4.
ND66 IC Cylinder
For more information call
Technical Support at 877-671-7011.
c
Reinstall adjustment plate.
Tighten until plate contacts door
thickness insert fl at.
© 2012 Ingersoll Rand
Printed in U.S.A.
P515-167 Rev. 06/12-e
If applicable, adjust turn button
position.
1³⁄₄" (44 mm)
1³⁄₈" (35 mm)
2" (51 mm)
2¹⁄₈" (54 mm)
1⁵⁄₈" (41 mm)