Bosch ANGLE EXACT 2 Manual Original página 24

24 | English
Removing the application tool
Press the pin in the recess of the application tool (1) inwards
and pull the application tool off the tool holder (2).
Changing the tool – screw head with hexagon
socket (see figure E)
When fitting an application tool, make sure that it is
u
held securely in the tool holder. If the application tool is
not held securely in the tool holder, it may become loose
and consequently uncontrollable.
ANGLE EXACT 2 | 3 | 6 | 7 | 8 | 15
An angled screw head with a 1/4" hexagon socket is avail-
able for these industrial cordless angle wrenches (article
number 0 607 453 618).
Inserting the application tool
Push the application tool (1) into the internal hexagon of the
tool holder (2) until you hear it engage.
Removing the application tool
Pull the application tool (1) off the tool holder (2), using pli-
ers if necessary.
Operation
Use personal protective equipment. Always
wear eye protection. Protective equipment
such as a dust mask, non-skid safety shoes,
hard hat or hearing protection used for appro-
priate conditions will reduce personal injuries.
Starting Operation
Always set the rotational direction using the rotational direc-
tion switch (14) before starting the power tool:
The power tool will not start if the rotational direction switch
(14) is in the centre (lock-off button).
Setting the rotational direction (see figure F)
Only push the rotational direction switch (14) when
u
the power tool is not in use.
Clockwise: To drive in screws, press the rotational direction
switch (14) all the way to the left.
Anti-clockwise: To loosen or unscrew screws, press the ro-
tational direction switch (14) all the way to the right.
Switching on the worklight
The worklight (18) illuminates the work area in poor lighting
conditions. Switch on the worklight (18) by lightly pressing
the on/off switch (13). If you press down harder on the on/
off switch, the power tool will switch on and the worklight
will remain illuminated.
Do not look directly into the worklight; it can blind
u
you.
Switching on/off
The screwdrivers have a torque-dependent
shut-off clutch that can be set to a value in the
specified range. It activates when the set
torque is reached.
1 609 92A 4V1 | (05.03.2019)
Note: If you are operating the screwdriver with a voltage ad-
apter, you will need to put the constant voltage regulator into
operation first.
To switch on the power tool, press the on/off switch (13)
down fully.
The power tool will switch off automatically when the set
torque is reached.
If the on/off switch (13) is released too early, the pre-
u
set torque will not be reached.
Practical advice
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Only apply the power tool to the screw/nut when the
u
tool is switched off. Rotating tool inserts can slip off.
Setting the torque (see figures G – I)
The torque depends on the spring preload of the shut-off
clutch. The shut-off clutch is triggered upon reaching the set
torque, both in clockwise and anti-clockwise rotation.
Only use the supplied adjustment tool (30) to set the indi-
vidual torque.
Slide the slider (7) on the power tool back completely.
ANGLE EXACT 2 | 3 | 6 | 7 | 8 | 15 | 17 | 23 | 30
Insert a hex key (31) into the application tool (30) and turn
it slowly.
Once a small protrusion (setting disc (32)) in the clutch can
be seen through the opening of the housing, insert the ad-
justment tool (30) into this protrusion and turn it.
ANGLE EXACT 14CF | 22CF | 29CF
Observe the information for your purchased flat drive or ask
your dealer.
Turning clockwise will result in a higher torque; turning anti-
clockwise will result in a lower torque.
Remove the adjustment tool (30). Slide the slider (7) to the
front again to protect the clutch from contamination.
Note: The required setting is dependent on the type of
threaded connector and can be best determined by practical
trials. Check a trial screw application with a torque spanner.
If you set the torque to a value outside the specified
u
power range, the shut-off clutch will not be triggered.
Marking the torque setting
ANGLE EXACT 2 | 3 | 6 | 7 | 8 | 14CF | 15 | 17 |
22CF | 23 | 29CF | 30
To label individually set torques, you can replace the mark-
ing ring (17) with a marking ring of a different colour.
If you use certain EXACT power tools with a torque of 4.5
Nm, for example, you can fit red marking rings on these to
identify the set torque. If you use other EXACT power tools in
a different assembly area with a torque set to 7.5 Nm, you
can fit a marking ring of a different colour (black, blue, green
or yellow) to identify the torque in this area. The different
marking ring colours are only intended as an aid for fitters to
Bosch Power Tools