Transportation And Storage; Troubleshooting; Technical Data; Warranty - GreenWorks G40PSF Manual Del Operador

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 15
EN
the inside of the guide bar is worn and make the chain
lean to one side.
5
TRANSPORTATION AND
STORAGE
Before you move the machine, always
Remove the battery pack from the machine.
Keep hands clear of the lock-out button.
Put the scabbard on the guide bar and the chain.
Before you put the machine into storage, always
Remove all residual oil from the machine.
Remove the battery pack from the machine.
Clean all unwanted material from the machine.
Make sure that the storage area is
Not available to children.
Away from agents which can cause corrosion, such as
garden chemicals and de-icing salts.
6

TROUBLESHOOTING

Problem
The machine does
not start
The bar and chain
gets hot and
smokes.
Possible cause
Solution
The poles are not
Assemble the
assembled cor-
poles according to
rectly.
the instructions.
1. Push and hold
the lock-out
button
2. While you
The lock-out but-
hold the lock-
ton and trigger are
out button,
not depressed at
pull the trig-
the same time.
ger.
3. Release the
lock-out but-
ton to start the
machine.
Oil tank is empty. Fill the oil tank.
Refer to the man-
The discharge
ual to remove the
port is blocked.
bar and clean out
the debris.
1. Clean the oil
tank.
Inlet opening of
inner oil tank is
2. Fill with clean
blocked.
bar and chain
lubricant.
The sprocket is
1. Clean the
stuck and clogged
sprocket.
with debris.
2. Fill with clean
bar and chain
lubricant.
English
Problem
The bar and chain
gets too hot and
can not cut.
The motor runs,
but the chain does
not cut correctly,
or the motor stops
after around 3
seconds.
7

TECHNICAL DATA

Voltage
No load speed
Guide bar length
Chain stop
Chain oil capacity
Weight (without battery
pack)
Measured sound pressure
level
Guaranteed sound power
level
Vibration
Chain
Guide bar
Battery model
8

WARRANTY

(The full warranty terms and conditions can be found on
Greenworks webpage)
The Greenworks warranty is 3 years on the product, and 2
years on batteries (consumer/private usage) from the date of
purchase. This warranty covers manufacturing faults. A faulty
product under warranty might be either repaired or replaced.
A unit that has been misused or used in other ways then
described in the owner's manual might be rejected for
warranty. Normal wear, and wear parts are not considered as
8
Possible cause
Solution
The chain tension
Refer to Adjust
is too tight or too
the Chain Tension
loose.
in the manual.
Sharpen or re-
The chain is dull
place the chain.
Refer to Replace
The chain is put
the Bar and Chain
on backwards.
in this manual.
1. Release the
When you use the
trigger.
machine under
2. Start the ma-
load, it stops.
chine again.
Lubricate the
The chain is not
chain to decrease
lubricated.
the friction.
40 V DC
8 m/s
203 mm
< 0.15 s
80 ml
8.2 Ibs (3.7 kg)
L
= 84 dB(A), K
pA
dB(A)
L
= 96 dB(A)
wA.d
2
< 2.5 m/s
, K = 1.5 m/s
91PJ033X/CL15033X
080NDEA318/
M1500833-1318TL
G40B2/G40B25/G40B4/
G40B5/G40B6 and other
BAF series
= 3
pA
2

Publicidad

Tabla de contenido
loading

Tabla de contenido