DeWalt P2201 Manual De Instrucciones página 9

Model P2201
Qualified Tool operaTor examinaTion
OPERATOR'S NAME
HOME ADDRESS
AGE DATE Of bIRTH
3
☐ Check the correct answer
1 It is necessary to read the Operator's Manual prior
to operating a D wALT low velocity tool.
E
☐ ☐
True false
2 when fastening into concrete, the base material
should be greater than the shank penetration by at
least: ☐ 1 time ☐ 2 times ☐
3 when operating a powder actuated tool, your hand
should never be placed:
☐
around the tool body
☐ in front of the tool muzzle
☐ over the tool handle
4 To determine the suitability of a base material, use
the fastener as a center punch.
• If the fastener is blunted, do not fasten; the material
is too:
☐ ☐ ☐
soft hard brittle
• If the fastener penetrates easily, do not fasten; the
material is too:
☐ ☐ ☐
soft hard brittle
• If the material cracks or shatters, do not fasten; the
material is too:
☐ soft ☐ hard ☐ brittle
5 Unsafe applications for powder actuated tools may
be caused by which of the following?
☐
a soft base material
☐
improper powder load
☐ fastening too close to an unsupported edge
☐
a malfunctioning tool
☐
fastening into a spalled area
☐ fastening through a pre-existing hole
☐
all of the above
6 which one of the following building materials is not
suitable as a receiving material (base material) for
powder actuated fasteners?
☐ sheet rock ☐ wood ☐ fiberglass
☐ ☐
sheet metal all of the above
liCenSe anD WaRRanTy aCTivaTion
The P2201 Tool iS WaRRanTeD FoR 3 yeaRS FRoM DaTe oF PuRChaSe on ManuFaCTuReRS DeFeCTS.
I certify that I have read and understand the P2201 Tool Operating Instruction Manual and have taken the Operator's exam. I understand the
importance of following all safety procedures and that failure to read, comprehend, and follow the detailed rules and warnings regarding the
safe operation of powder actuated tools can result in serious injury or death to the tool operator or bystanders. I agree to conform to all the
rules and regulations regarding the use of powder actuated tools.
THE SERIAL NUMbER ON MY TOOL IS:
PLEASE SENd My TOOL LICENSE TO:
NAME
ADDRESS
CITY
Tool License Coordinator • D
MAIL TO:
P2201
7 when considering the safety of a particular
application, the operator must think about:
☐
the base material
☐
the powder load power level
☐ the operator's safety
☐
the safety of bystanders and fellow workers
3 times
☐
all of the above
8 The proper loading procedure is: insert fastener first,
powder load second. The fastener should always be
placed in the tool prior to the load.
☐ True ☐ false
9 which one of the following materials is usually
suitable for powder actuated fastenings?
☐
poured concrete
☐ surface hardened steel
10 In concrete, a fastener should be driven no closer to
an unsupported edge than:
☐ ☐
1/2" 1-1/2"
11 fishhooking is a condition which can occur when
a powder actuated fastener strikes a piece of hard
aggregate or very hard concrete, bends and comes
out of the work surface. A fishhook can cause a
serious injury or death.
☐ True ☐ false
12 Placing a hand over the muzzle bushing of a
loaded tool can result in serious injury from piston
overdrive or an escaping fastener if the tool is
discharged accidentally.
☐ ☐
True false
13 Piston overdrive is caused by overpowering of
the tool or by discharging the tool against a soft
surface.
☐ True ☐ false
14 Malfunctioning tools cannot be used and must be
removed from service immediately.
☐ ☐
True false
STATE
WALT, Inc.• 2 Powers Lane, Brewster, NY 10509
e
COMPANY NAME
COMPANY ADDRESS
COMPANY PHONE
SIGNATURE
15 After conducting a Center Punch Test,the best
way to check the base material is to set several
fasteners using the least powerful load.
☐
16 Eye protection and hearing protection should not be
worn by the operator and any necessary bystanders
when using the tool.
☐
17 A powder actuated tool cannot be safely used in an
explosive or flammable atmosphere.
☐
18 List the proper powder load level number
(1-6) next to each color listed.
☐
hollow tile
Red ___
☐ glazed brick
Yellow ___
19 The weakest power level should be used when
making the first fastening.
☐
3"
☐
20 You can fasten into welded areas of steel.
☐
P2201
• The proper procedure if a powder load fails to ignite
is to hold the tool against the work surface and wait
30 seconds, then proceed exactly as directed in the
Operator's Manual.
☐
• D
E
caliber, "A" tapered, neck down, rim fire, short
crimped cartridges. No other powder load may be
used in this tool.
• Operators should never compress the P2201 or any
other powder actuated tool against any part of their
body.
• If a piston buffer for the P2201 becomes deformed,
simply remove it, and use the tool without the
buffer?
(Please print clearly)
zIP
9
Cat. No. DDF211022P
DATE
☐
True false false
True ☐ false
☐
True false
brown ___ Green ___
Gray ___ Purple ___
☐
True false
True ☐ false
☐
True false
wALT powder loads for the P2100 are .22
☐ True ☐ false
☐ True ☐ false
☐ ☐
True false
PHONE