Technical Data - AEG US 900 XE Manual Original

TECHNICAL DATA

US 900 XE
Rated input .................................................................. 900 W
Stroke rate under no–load .................................. 0 - 3500 min
Lengths of stroke .......................................................... 19 mm
Weight without cable ................................................... 2,9 kg
Noise/Vibration Information
Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A)) ............................ 89,5 dB (A)
Sound power level (K = 3 dB(A)) .............................. 100,5 dB (A)
Wear ear protection!
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Sawing of wood
Vibration emission value a
Uncertainty K ............................................................... 1,5 m/s
GB
WARNING
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in
EN 60 745 and may be used to compare one tool with another It
may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for diferent
applications, with diferent accessories or poorly maintained, the
vibration emission may difer. This may signiicantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched of or when
it is running but not actually doing the job. This may signiicantly
reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator
from the efects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
WARNING!
Read all safety warnings and all instructions, including
those given in the accompanying brochure. Failure to follow
the warnings and instructions may result in electric shock, ire
and/or serious injury. Save all warnings and instructions for
future reference.
SAFETY INSTRUCTIONS
Wear ear protectors. Exposure to noise can cause hearing loss.
Hold power tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a "live"
wire will also make exposed metal parts of the power tool
"live" and shock the operator.
Appliances used at many diferent locations including open air
should be connected via a residual current device of 30 mA or less.
Always wear goggles when using the machine.
It is recommended to wear gloves, sturdy non slipping shoes and
apron.
Sawdust and splinters must not be removed while the machine is
running.
English
8
Reciprocating saw
.........................................19,1 m/s
h
Always disconnect the plug from the socket before carrying out any
work on the machine.
Only plug-in when machine is switched of.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
-1
Always use the protective shields on the machine.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft
materials (wood, light building materials for walls). Harder
materials (metals) must irst be drilled with a hole corresponding to
the size of the saw blade.
When working in walls ceiling, or loor, take care to avoid electric
cables and gas or waterpipes.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Wear a suitable dust protection mask.
2
SPECIFIED CONDITIONS OF USE
2
This sabre saw cuts wood, plastic, and metal. It can cut straight
lines, curves, and internal cut-outs. It cuts pipes and can cut lush
to a surface.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized documents.
EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3,
in accordance with the regulations 2006/42/EC, 2004/108/EC
Winnenden, 2010-07-30
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the system
voltage indicated on the rating plate.
It is also possible to connect to sockets without an earthing contact
as the design conforms to safety class II.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Use only AEG accessories and AEG spare parts. Should components
need to be replaced which have not been described, please contact
one of our AEG service agents (see our list of guarantee/service
addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type printed
on the label and order the drawing at your local service agents or
directly at: AEG Electric Tool, Max-Eyth-Straße 10,
D-71364 Winnenden, Germany.
Rainer Kumpf
Manager Product Development
Authorized to compile the technical ile.