Bestway Lay-Z-Spa Manual Del Usuario página 15

Lock/Unlock Button
The pump has a 5-minute auto-lock. The LED light will dim out when the pump is locked (no function is
activated).To lock or unlock the pump, place a finger over the lock/unlock button for 3 seconds.
Lay-Z-Massage System Button
Use this button to activate the massage system, which has a 30-minute auto-shutoff
feature.
The light above the Lay-Z-Massage system button displays red when activated.
IMPORTANT: Do not run the Lay-Z-Massage system when the cover is attached. Air
can accumulate inside the spa and cause irreparable damage to the cover and bodily
harm.
NOTE: Heat and massage system work together to create a warm massage experience.
HydroJet System Button
This button turns the water pump on and off. The light above the HydroJet system button displays red when activated.
Note: The system will shut off automatically after 1 hour.
Note: Do not dry run the HydroJet System.
Heat Button
Use this button to activate the heating system. When the light above the heat button is red, the heating system is activated. When the light is
green, the water is at the set temperature and the heating system is at rest.
NOTE: If the heating system is activated, the filtration system will automatically start.
NOTE: After turning off the heating system, the filtration system will continue to operate.
Water Filter Button
This button turns the filter pump on and off.
The light above the Water Filter Button displays red when activated.
NOTE: The built-in hard water treatment function works automatically.
Power-Saving Timer Button
This is a newly added function, designed to help avoid wasting power by setting the time and duration of the heating cycle for the spa.
This way, you can enjoy your spa at the time you desire, without needing to leave the heater on at all times.
STEP 1: Set the heating duration
1. Press the button unit the
2. Press the or button to adjust the heating duration (From 1-48 hours).
3. Press the button again to confirm the heating duration.
STEP 2: Set the number of hours FROM NOW when the heater will activate
1. After setting the heating duration, the
2. Press the or button to adjust the hours until time of activation (From 0-99 hours).
3. Press button again or simply touch nothing for 10 seconds to confirm the setting.The
To modify the timer settings: Press the
Cancel the setting: Press the
NOTE: After setting, the screen flashes the current temperature and time alternately.
NOTE: Timer adjustment (amount of time with the heater ON) may be set from 1 to 48 hours;
Reservation time adjustment (the number of hours FROM NOW when the heater will begin to function) may be set from 0 to 99 hours. If the timer is set at 0 hour, it
means the Timer function is not set.
Note that the timer is one time per use - the user sets the duration of the heating cycle, and how many hours from now the heating cycle begins. The timer does NOT
repeat until reset.
Celsius/Fahrenheit Toggle
The temperature can be displayed in either Celsius or Fahrenheit.
Temperature Adjustment Buttons
Pressing the Temperature Increase or Decrease buttons will cause the LED to flash.
When it is flashing you can adjust to the desired temperature setting. If you hold these buttons down, the values will rapidly increase or
decrease. The new and desired temperature setting will remain on the LED display for 3 seconds to confirm the new value.
NOTE: The default temperature is 35°C (95°F).
NOTE: Temperature adjustment ranges from 20°C (68°F) to 40°C (104°F).
Power-Saving Timer LED
This LED flashing means you are setting the heating duration. The light will be on when the heating function starts to work.
This LED flashing means you are setting the number of hours FROM NOW when the heater will activate. When the light is on, the Power-Saving
Timer function is set.
On/Off Button
Press this button for 2 seconds to active the control panel bottons and the light turns to green.
Press this button for 2 seconds to turn off all currently activated functions.
LED Display
Once powered up, the LED displays the current water temperature automatically.
After 72 hours of filtration (without using the power saving timer function), the pump will hibernate and flash "End" with the current water
temperature. When the pump is hibernating both the heating and water filter functions are disabled. To re-active the pump press lock/unlock
button for 3 seconds.
NOTE: The water heat rate may change in the below conditions:
· When the outdoor temperature is below 15°C (59°F).
· If the cover is not in position when the heating function is activated.
NOTE: To display the current water temperature, run the filter system for at least a minute. The water temperature as tested by an external thermometer
may vary from the temperature as displayed on the spa panel due to the differing positions of the measurement devices.
•Keep good circulation when the spa enters a filtration purge cycle, it is good practice that on exiting the spa, all massage jets are left open, aeration
valves are closed and diverters are set half way to allow chemically treated water to flush through all pipework.
•Whenever the spa is emptied, the filter should be cleaned (and drained/dried).
•In the absence of automated and/or continuous water treatment (measurement and
chemical dosage) any manual dosing of chemicals shall not be performed while bathers are present in the spa.
303021213751_14x21cm_54138;54173_
LED starts to flash.
LED starts to flash.
button and use the or button to adjust.
button for 2 seconds.
HydroJet SPA _
LED will light steadily, and the countdown to heater activation will begin.
15
HYDROJET PRO