Work Area - Rubi TC-125 Manual De Instrucciones

12.
check for dents or deformations and broken parts and
cords. If any of these are found, do not use the electric
tool and contact the manufacturer immediately.
6) Keep hands away from the cutting area and blade at
all times. Keep the hand that is not being used on the
secondary handle. Your hands cannot be cut by the
blade if they are both holding the cutter.
7) Do not place your hand under the piece that is being
cut.
8) Hold the tool by the insulated surfaces when carrying
out operations in which the cutter could come into
contact with hidden wires or its own power cord.
Contact with a live wire could cause the current to be
transmitted through the metal parts of the machine
and cause a strong electrical shock to the operator.
9) Always use blades with interior diameters that
correspond to the machine's shaft. A larger
interior diameter would cause the cutter to rotate
eccentrically, leading to a loss of control.
10) Never use plates or anchor screws from damaged
or incorrect blades. These parts were designed
specifically for this cutter, to provide better functioning
and safety during operation.
11) Hold the cutter firmly and position your body and
arms in such a way that you can resist the forces of
KICKBACK. KICKBACK forces can be controlled by the
operator if the proper precautions are taken.
12) Do not use damaged or dull blades.
13) Use only the recommended blades, suitable for RPMs
that are greater than or equal to the maximum RPM of
the machine and with holes for the proper shaft.
14) Position the blade plates correctly and tighten the
screw properly before starting up the machine.
15) Check the interior surfaces of the blade anchor plates,
as well as the sides of the blade, in order to avoid any
problems.
16) Verify that the blade has no cracks or other damage
before operation. Immediately replace damaged
blades. Do a functional test with no load for at least 30
seconds before using the cutter.
17) Never start the machine with the piece being cut in
contact with the blade.
18) Allow the motor to reach its maximum speed before
cutting.
19) Important: after completing the cut, release the
switch and wait for the blade to stop completely
before setting the cutter down.
20) Do not use the machine in areas with flammable
solids, liquids or gases. The sparks produced in the
brushes could cause a fire or explosion.
21) This machine was designed for specific applications.
The manufacturer certifiably recommends that it not
be modified and/or used for applications other than
the ones for which it was designed. If you have any
questions regarding the use of the machine, do not
use it until you have consulted the manufacturer and
received the corresponding information.
22) Only use the machine for cutting ceramic, stoneware,
porcelain and natural stone.
23) Use the secondary handles provided with the tool.
Loss of control can result in injury.
24) Use the residual current device (PRCD). The PRCD
unit disconnects electrical power supply to the tool
automatically when a leak is detected in the device,
or when there is a risk that the user could receive an
electrical discharge.
25) Keep the power cord away from the machine's
cutting zone. Always keep the power cord away from
the machine behind you.
26) Turn off the machine immediately if you notice any
unusual vibration or any other malfunction. Check the
English
TRANSLATION OF THE ORIGINAL
27) Use only the diamond blades recommended by the
28) Pay attention to the dimension of the blades. The
29) Try to avoid electrical lines, gas and water pipes.
30) The dust that is produced when working with

2.3 Work area

Work position
3.- OPERATING INSTRUCTIONS
3.1 Assembly instructions
After unpacking the machine, carefully check for
damaged or broken parts. If you find any damaged or
malfunctioning parts, replace them with original spare
parts from the manufacturer and contact RUBI's after-
sales service.
Installing and replacing the blade:
1. The blade is installed at the factory. To install the
2. Move the side guard out of the way. (Fig. A-8)
3. Move the black guard up until the blade area is clear.
4. Remove the screw (clockwise) and remove the outer
5. The interior blade plate must be installed on the
6. Install the exterior plate as shown in the image and
7. Install the blade guard, the side guard and the suction
Connection of the water feed system:
8. The feed system is installed at the factory. The valve is
9. Make sure that all of the parts of the assembly are
10. Make sure that the suction intake cover is properly
machine to determine the cause.
manufacturer.
centre hole in the blade must fit on the shaft with no
free play. If not, a reducer washer (provided with the
blade) will be needed to ensure proper fit.
Inspect your work area, for example with a metal
detector, before starting work.
this tool may be harmful to your health. Use an
absorption system and wear a suitable dust mask.
When the cutting operation has been completed,
clean any deposited dust with a vacuum cleaner.
blade, set the machine to the maximum height using
the depth adjustment lever. (Fig. A-10)
If necessary, also remove the cover of the suction
intake. (Fig. A-7)
blade plate (spanners included). (Fig. B)
machine's shaft, as shown in the image. Put the
interior blade plate in position, orienting it according
to the direction of rotation indicated on the machine.
(Fig. B-4)
tighten the screw firmly by turning counter-clockwise
(spanners included).
intake cover in their original positions. (Fig. C)
oriented at a 45º angle for greater comfort.
properly secured and the water regulation valve is in
the perpendicular position. (Fig. D-12)
installed on the machine. (Fig. C-15)