Package Contents; Description (Fig. A) - DeWalt DWH201D Traducido De Las Instrucciones Originales

EngLIsh

Package Contents

The package contains:
1 Dust extraction system
1 Side handle
1 Long tube
1 Short tube
1 Dust port plug
1 Wear ring
1 Dust hose
1 Adapter for rotary hammers
1 Adapter for hammer drills
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Dust Extraction System
The following pictograms are shown on the tool:
Read instruction manual before use.

Description (Fig. A)


WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Side handle
1
Short tube
2
Long tube
3
Dust extraction connection
4
port
Wear ring
5
Intended Use
The DWH201D dust extraction system has been designed
for the extraction of dust in professional hammer drilling in
masonry or concrete, and with solid drill bits mounted to
the power tool. This dust extraction attachment will fit most
D WALT corded and cordless SDS PLUS rotary hammers,
e
corded hammer drills and premium cordless drill/driver/
hammer drills. For more information about D
tools compatible with this attachment, please contact your local
dealer, refer to the addresses at the back of the manual or visit
www.dewalt.com.
DO nOt use under wet conditions or in the presence of
flammable liquids or gases.
The dust extraction system is an attachment for use with
professional power tools.
DO nOt let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
12
Dust hose
6
Adapter for rotary
7
hammers
Adapter for hammer drills
8
Dust port plug
9
WALT power
e
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
SPECIFICATIONS
Short tube To be used with 150 mm overall length (100 mm useable) bits.
Long tube To be used with 250 mm overall length (200 mm useable) bits.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Attaching and Removing the Dust Extraction
System
To Attach the Dust Extraction System (Fig. A–D)
1. Remove the bit prior to assembling.
2. Remove the side handle and the depth adjustment rod, if
attached to the tool.
3. Widen the ring opening
17
anti-clockwise.
4. Slide the assembly onto the nose of the tool, through the
ring opening and onto the collar
17
holder and sleeve. If an adaptor is needed refer to Attaching
the Dust Extraction System with an Adapter.
5. Rotate the dust extraction system to the desired position.
6. Lock the assembly in place by securely tightening the side
handle 1 , rotating the grip clockwise so that the assembly
will not rotate.
7. Insert the dust hose into the dust extraction connection
6
port and a dust extractor (not shown).
4
nOtE: The dust exrecation system is compatible with or
without a dust extractor. The tool can be used with the
plug 9 inserted in the dust extraction connection port
you are using the plug, it is recommended you remove the
dust from the tube after drilling each hole.
attaching the Dust Extraction system with an adaptor
(Fig. a, D)
If the diameter of the tool's collar
adaptor is needed to properly mount the dust extraction system.
Your dust extraction system comes with two adaptors, a
toothed adaptor for rotary hammers
for hammer drills 8 .
1. Choose the correct adaptor.
2. Open correct adaptor and close onto the collar
nOtE: The adaptor will slide back and forth on the tool.
3. Widen the ring opening 17
anti-clockwise.
4. Place the ring opening
17
by rotating the side handle
1
, past the chisel
10
4
10 is less than 43 mm, an
and a smooth adaptor
7
.
10
by rotating the side handle 1
onto the adaptor.
. If