JUNO JCLR6 Retrofit Trim Serie Instrucciones De Instalación

WARNING: For your safety, read and understand instructions completely before starting installation. Before wiring to power supply, turn
off electricity at the fuse or circuit breaker box.
NOTE: Juno recessed products are designed to meet the latest NEC requirements and are classified in compliance with applicable UL
standards. Before attempting installation of any recessed lighting product, check your local electrical building code. This code sets the
wiring standards and installation requirements for your locality and should be understood before starting work.
SAVE THESE INSTRUCTIONS
Product Information
Juno's JCLR6 and JCLR8 LED trims may be used as retrofit trims for 6" and 8" incandescent, CFL or H.I.D open frame rough-in sections.
Suitable for damp locations.
The JCLR6 and JCLR8 Retrofit trims consist of the following: Reflector, Optic Lens
Assembly, Trim Ring, LED Driver/Driver Junction Box, Conduit Whip Assembly, Conduit
Fitting, Qty 6 Friction Clips and installation instructions (In hardware bag). Check for all
contents prior to installation (Refer to Figure 1).
Do not make or alter any open holes in an enclosure of wiring or electrical components
during kit installation.
WARNING - Risk of fire or electric shock.
• Installation of this retrofit assembly requires a person familiar with the construction and
operation of the luminaire's electrical system and the hazard involved. If not qualified, do
not attempt installation. Contact qualified electrician.
• Install this kit only in luminaires that have the construction features and dimensions
described in these instructions, and where the input rating of the retrofit kit does not
exceed the input rating of the luminaire.
AVERTISSEMENT - Risque d'incendie ou d'électrocution
• L'installation de cet assemblage modifié exige une personne familière avec la construction et le fonctionnement du circuit électrique de
l'appareil d'éclairage et les risques encourus. Si vous n'êtes pas qualifié, n'essayez pas le montage. Mettez-vous en rapport avec un
électricien qualifié.
• Ne montez ce nécessaire que sur des luminaires dotés des caractéristiques de construction et des dimensions décrites dans ce mode
d'emploi, et où la classification de débit calorifique du nécessaire d'adaptation n'excède pas la classification de débit calorifique du luminaire.
WARNING - To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
AVERTISSEMENT - Afin d'éviter tout endommagement ou abrasion du câblage, ne mettez pas en contact le câblage avec les arêtes de la tôle
ou d'autres objets tranchants.
IMPORTANT - Trims must be grounded as outlined below. Failure to do so can result in electric shock or undesired operation. The trim assembly
must be electrically grounded either through the conduit whip/junction box connection or through the friction clips contact with rough-in section.
This requires that the rough-in section junction box be electrically grounded.
To use this product in an ungrounded rough-in section, consult factory for additional instructions.
IMPORTANT - Power to the luminaires must be turned off prior to installing these LED retrofit trims. Failure to do so can cause electric shock,
which can result in injury or death.
THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL
BE DETERMINED BY CSA OR AUTHORITIES HAVING JURISDICTION.
Dimming
Universal input voltage (120VAC thru 277VAC)
and 347VAC. Retrofit dimmable with the use of
most 0-10V wall box dimmers.
Consult Juno Product Services or website for compatibility.
*Electronic low voltage dimmers require a neutral wire connection in the wall box.
Juno JCLR6 and JCLR8 Retrofit LED Trim Compatibility
Commercial Rough-In Section Compatibility
The JCLR6 and JCLR8 retrofit trims are provided with spring
steel friction clips allowing for installation in a variety of 6" and 8"
commercial recessed open frame rough-in sections with a ceiling
thickness ranging from 1/2" to 1 1/8":
Rough-in section inside diameter compatibility range:
JCLR6S: 6" - 6 1/2", JCLR6L: 6 5/8" - 7 1/8".
JCLR8S: 7 13/16" - 8 5/16", JCLR8L: 8 5/8" - 9 1/8".
Rough-in section compatibility can be determined by measuring
the rough-in section as shown in Figure 2.
1300 South Wolf Road • Des Plaines, IL 60018 • Phone 800-323-5068 • www.junolightinggroup.com
INSTALLATION INSTRUCTIONS
For JCLR6 and JCLR8 Retrofit Trim Series
120VAC input voltage. Retrofit dimmable with the
use of most incandescent, magnetic low voltage
or electronic low voltage* wall box dimmers.
Conduit Whip
Reflector
Trim Ring
Figure 1
Inside
Ceiling Thickness
Diameter
Figure 2
© 2016 Acuity Brands Lighting, Inc.
Conduit Fitting
(1/2" Trade-Size)
Assembly
LED
Driver
Driver Junction
Box
Optic Lens
Assembly
Rev 8/16 P5520 pg 1 of 2