Worx WG183 Manual De Instrucciones página 10

Two, three or four
green lights are
illuminated.
Only one green
light (
is illuminated.
No light is
illuminated.
Only one light is
flashing twice per
cycle.
Only one light is
flashing three
times per cycle.
Only one light is
flashing four times
per cycle.
OPERATION INSTRUCTIONS
WARNING! The charger and battery pack are
10 specially designed to work together so do not
attempt to use any other devices. Never insert or allow
metallic objects into your charger or battery pack
connections because of an electrical failure and hazard
will occur.
1. AUTOMATIC LINE FEED SYSTEM
When initially switching on the trimmer, a small length of
line is fed out.
A 'clattering' noise will be heard for a short time. This is
normal and is caused by the line being cut by the line
cutter. Once the line is cut to the correct length, the
'clattering' noise will stop and the trimmer motor will run
at full speed.
To feed more line, stop the trimmer completely, then
restart, allowing the motor to reach full speed. Repeat
this until you hear the 'clattering' noise of the line
cutting. (Do not repeat this procedure more than 6 times)
2 . MANUALLY FEEDING THE LINE (See Fig. H)
Press and release manual line feed button, whilst gently
pull out the lines until the lines reaches the line cutter.
When the required amount of line is fed out, gently pull
on the second line (there is no need to press the manual
line feed button again). If the line extends past the line
cutter, too much line has been fed out. If too much line is
fed out, remove the spool cap and rotate the spool anti-
clockwise until the line is at the desired length.
Removing the Cap (See Fig. I)
Press and hold in the two latches. Pull the spool cap
away from the Cutting Head. Keep the cap and spool
Cordless Grass Trimmer
The two batteries have a
remaining charge. The more lights
are illuminated, the more battery
capacity.
At least one battery is almost
) depleted and needs to be
charged.
At least one battery is not fully
installed or battery may be
defective.
At least one battery is over
discharged (please refer to
the battery charge condition),
please recharge the two
batteries at once before use
again or storage.
At least one battery is hot, wait
for them cool down before start
again.
The machine is over load. Raise
the cutting height or push
slowly.
holder clean from debris. To replace the cap, press it
firmly towards the spool holder. Ensure that it is correctly
connected by trying to remove it without depressing the
two latches.
Changing the Line Spool (See Fig. K, L)
First take off the cap and remove the old spool. Place
new spool into cutting head. Feed one line through the
eyelet, then repeat for second line (See Fig. L).
Release line from cleat on the Spool. Reattach the cap.
WARNING! Your Trimmer is designed to only use
line with a maximum diameter of 0.065"(1.65mm).
Only use nylon line.
IMPORTANT - Always wind the line onto the upper
section of the spool first.
3. Manually winding the line (See Fig. M, N, O, P)
Take approximately 16ft (5 m) line and insert 5/8" (15
mm) of line into one of the holes in the upper section of
the spool. Wind the line in the direction of the arrows on
the top of the spool.
Leave approximately 3.9'' (100mm) of line unwound
and place it into the cleat. Repeat on the lower section
of spool. Care should be taken to ensure that the line is
neatly coiled on the spool. Failure to do so will impair the
efficiency of the automatic line feed. Then fit the spool
as described above in "Changing the Line Spool".
STORING YOUR GRASS
TRIMMER
Always remove the battery pack from
your trimmer after use.
To store your GRASS trimmer
The trimmer is provided with a hanging slot for
storing the trimmer on the wall. (See Fig. Q)
Store in a dry place where the trimmer and battery
can be protected from damage.
MAINTENANCE
Always remove the battery pack from your
trimmer after use.
Always check the product prior to being used for
any damage.
After use, disconnect the battery from the tool and
check for damage.
Your power tool requires no additional lubrication or
maintenance. There are no user serviceable parts in
your power tool. Never use water or chemical cleaners
to clean your power tool. Wipe clean with a dry cloth.
Always store your power tool in a dry room temperature
location. Keep the motor ventilation slots clean. Keep
all working controls free of dust.
FOR BATTERY TOOLS
The ambient temperature range for the use and storage
EN