General Product Description; General Instructions; Detergent Injector; Safety Instructions - Electrolux WT150 Instrucciones De Funcionamiento

General product description

General instructions

If the instructions in this and the equipment's other
documents are not followed, its safety could be jeo-
pardised, and the supplier's guarantee and product
responsibility will become invalid.
• Read the instructions in this document carefully, as it
contains important safety information concerning in
stallation, operational safety, usage and maintenance.
Keep it in a place which is accessible to all users.
• All servicing, maintenance and repairs must be car-
ried out by qualified technicians. Only original spare
parts may be used.
• Maintenance and operation may only be carried out by
personnel specially trained for this purpose (operator).
Use
Electrolux Rack type dishwasher WT150 / WT190 is de-
signed for washing porcelain, glass, cutlery, contai-
ners and lids as well as different types of kitchen uten-
sils.
This machine is designed for the above application
and must not under any circumstances be used in any
other way or for any other purpose than described in
this user's guide.
Specially designed racks, which can be fitted with differ-
ent inserts, provide practical and easy handling as well as
a superb washing result. The racks are transported
automatically through the machine's different zones.
WT 150 washes up to 150 racks per hour on the high speed
and 100 racks per hour on the low speed, which is adapted
for heavily soiled tableware.
WT190 washes up to 188 racks per hour on the high speed
and 125 racks per hour on the low speed, which is adapted
for heavily soiled tableware.
This appliance has been developed to meet the increased
demands of a good working environment and good econo-
my. The dishwasher works at a low noise level and with
very little heat emissions.
The electronic version (E2), gives a clear overview of the
wash process. The panel has, among others, a function for
fault indicating.
On the electromechanical version (E1) the indicating lamps
on the front panel show fault indications for open door, water
level not reached or non-functioning wash pumps.
If the dishwasher is equipped with a condensing unit (CU)
it recovers heat from the damp and hot steam instead of
releasing it into the washing room. In the same way the
complete energy saving device, ESD, comprising of a heat
exchanger in combination with a condensing unit, recov-
ers excess heat from the steam and from the final rinse
water.
A dishwasher equipped with ESD also works with a
special
water return flow via the heat exchanger, which means
that the amount of water replaced is only 60 litres/hour.
As standard the dishwasher is equipped with a normal
sized pre-wash zone, which requires manual clearing and
rinsing of the tableware. The larger pre-wash zone is an
option that allows this work to be reduced.
The pre-wash and the wash zones have flat filters
which cover the entire width of the tanks. The filters
slant towards against the deep basket filter that
collects the food waste.
Each wash zone is fitted with automatic temperature
control. The temperature of the various wash tanks
appears on the panel display/thermometers.
To drain a tank, just open the door and raise the
overflow rod. The drain is then closed automatically
when the door is shut.
The wash tanks are made of sheet stainless steel with
softly rounded corners facilitating cleaning.
The wash arms can be lifted out for checking and clean-
ing. The fine strainer in the final rinse zone prevents block-
age of the DUO-rinse nozzles.
The final rinse works with DUO-rinse. The clean and hot
water from the rinse water heater goes directly to the last
of the two final rinse arms, it is then pumped up to be fed
through the first rinse arm. A part of the used rinse water
is directed to the wash tank.
All rack type dishwashers can be fitted with a hot air blow-
er or drying zone.
The machine is designed to provide good accessibility for
servicing and maintenance.
CE- Directive (fig 1)
WT150 / WT190 is manufactured in compliance with EU-
directives MD 89/392/EEC ANNEX IIB, EMC 89/336/EEC,
LVD 73/23/EEC and is intended for use installed in/to-
gether with equipment which fulfils applicable EU-
directives. The appliance may not be put into use before
the plant of which it is a part has been declared in
compliance with current EU-directives.

Detergent injector

• Only detergent injectors which comply with applica-
ble instructions may be connected to the machine.
• Detergent injectors may not be connected in such a
way that the machine's function or safety is at risk.

Safety Instructions

Turn off the electricity supply before defects or break-
downs in function are repaired, or if goods have jammed
or fallen into the machine.
• (E1) Turn the "On/Off" switch to the 0 position.
• (E2) Press the button "O".
• Switch off the "Main" switch.
If the machine is connected to the mains via a multi-pole
safety-switch, the current can be broken by means of
this.
31