Tabla de contenido
Publicidad
If upon cleaning your blades you find that the blades will still not cut, there may
be a few fine pieces of hair trapped between the upper and lower blade. If this
happens, you will need to snap the blade off the clipper. Proceed to slide the
upper blade to one side, without loosening the tension spring or moving the
upper blade completely out from under the tension spring (See Figure G for
position of blade). Wipe the surface between the blades clean with a dry cloth,
then place a drop of clipper oil where the upper and lower blades meet and also
in the guide slot of the tension spring (Figure G). Now slide the upper blade to
the opposite side of the lower blade and repeat this process. After completing
this procedure, slide the upper blade, centering it over the lower blade. Handle
or store your Andis Clipper with the blades down so excess oil will not run into
the clipper case.
CHANGING THE BLADE DRIVE ASSEMBLY
If your clipper blades no longer cut properly (be sure to try more than one blade,
since the blade currently being used may be dull), it could be that your blade
drive assembly needs replacement.
To change the blade drive assembly:
1. Remove blade set (Figure C).
2. Remove drive cap (Figure H).
3. Remove blade drive mounting screws (Figure I).
4. NOTE: Before removing blade drive assembly, note the way it is positioned
(this will help you in reassembly). Remove blade drive assembly (Figure J).
5. Drive bearing should be at its lowest position, if not, move it with your finger
to lowest position (Figures K & L).
6. Put on new drive assembly, align screw holes and press down (Figure J).
7. Reassemble blade drive by mounting screws (Figure I).
8. Replace drive cap (Figure H).
9. Replace blade (Figure E).
FACTORY REPAIR SERVICE
When the blades of your Andis clipper become dull after repeated use, it is
advised to purchase a new set of blades available through your Andis supplier
or through an Andis Authorized Service Station. Some blade sets can be
resharpened – contact Andis Company for information on resharpening. To find
an Andis Authorized Service Station near you log on to www.andis.com or
contact our customer service department: 1-800-558-9441 (U.S.) or
1-800-335-4093 (Canada).
Caution: Never handle your Andis clipper while you are operating a water
faucet, and never hold your clipper under a water faucet or in water. There is
danger of electrical shock and damage to your clipper. Andis Company will
not be responsible in case of injury due to this carelessness.
6
S P A N I S H
Sírvase leer las instrucciones siguientes antes de usar su nueva
recortadora Andis. Al brindar el cuidado que se merece un instrumento
fino construido con precisión, obtendrá muchos años de servicio.
PRECAUCIONES IMPORTANTES
Al usar un artefacto eléctrico, siempre deben seguirse ciertas
precauciones básicas, que incluyen la siguiente: Lea todas
las instrucciones antes de usar la recortadora de acabado
Andis.
PELIGRO:
Para reducir el riesgo de descarga
eléctrica:
1. Si un artefacto se ha caído al agua, no trate de sacarlo.
Desenchúfelo inmediatamente.
2. No lo utilice al bañarse en tina o bajo la regadera.
3. No coloque ni almacene el artefacto donde pueda caerse
en una bañera o un lavabo, o ser halado dentro de éstos.
No la coloque ni la deje caer en agua u otro líquido.
4. Siempre desenchufe este aparato del tomacorriente
eléctrico inmediatamente después de usarlo.
5. Desenchufe este artefacto antes de limpiar, desmontar o
montar las piezas.
ADVERTENCIA:
quemaduras, incendio, descarga eléctrica o lesiones a las
personas:
1. Un artefacto nunca debe dejarse desatendido mientras
está enchufado.
2. Es necesaria una supervisión estrecha cuando este
artefacto sea usado por, en o cerca de niños o personas
con ciertas discapacidades.
3. Utilice este artefacto exclusivamente para su uso
propuesto, tal como se describe en este manual.
No utilice accesorios no recomendados por Andis.
4. Nunca opere este artefacto si su cable eléctrico o
enchufe está dañado, si no está funcionando
Para reducir el riesgo de
7
Publicidad
Tabla de contenido
