Automatic Watch; Automatic Chronograph Watch - Hamilton 251.272 Manual De Instrucciones

3. Operating instructions
3.4 Automatic watch
A utomatic movement. The mechanism of the watch includes an oscillating rotor that winds the main-
spring via the motion of your wrist. The running reserve is approximately 42 hours. If necessary, the watch
may be rewound manually. With most of our models, the beauty of the inner working of the watch move-
ment can be admired through the transparent case back.
Caliber 2824-2 • 2826 • 2834-2 • 2836-2 • 2671 • 2892A2 • 2895-2 • 2897 • A07.511
Setting the time
1. Pull out the crown completely to position (p2): the seconds hand stops*.
C
2. Set the time by turning the crown in the desired direction.
3. Push the crown back in completely to position (p0): the seconds hand starts again, allowing perfect synchro-
nization with a time signal.
* stop seconds according to model
Setting the date and the day
1. Pull out the crown to position (p1).
C
2. Turn the crown clockwise to set the date and counterclockwise to display the desired day.
3. Push the crown back in completely to position (p0).
3.5 Automatic chronograph watch
Caliber 2894-2 • 2894-S2
Setting the time
1. Pull out the crown completely to position (p2): the seconds hand stops.
C
2. Set the time by turning the crown in the desired direction.
3. Push the crown back in completely to position (p0): the seconds hand starts again, allowing perfect synchro-
nization with a time signal.
Setting the date (only for 2894-2)
1. Pull out the crown to position (p1).
C
2. Turn the crown clockwise to set the date.
3. Push the crown back in completely to position (p0).
Using the chronograph / Start-Stop function
Timing a single event:
1. Press button A: the chronograph starts.
2. Press button A: the chronograph stops.
3. Press button to reset to zero.
B
Note: Before you start timing, the hands should be reset to zero. If necessary, press button B.
10
All manuals and user guides at all-guides.com
Cumulative time function
This measures successive times. Each result is added to the previous one.
1. Press button A: the chronograph starts.
2. Press button
Repeat these two steps as many times as desired. At the end of the last measurement, the chronograph displays
the total of all the times measured. Press button
Caliber 7750 • A07.211 • A07.211
Setting the time
1. Pull out the crown
2. Set the time by turning the crown in the desired direction.
3. Push the crown back in completely to position (p0): the seconds hand starts again, allowing perfect synchro-
Setting the date and the day
1. Pull out the crown
2. Turn the crown clockwise to set the date and counterclockwise to display the desired day.
3. Push the crown back in completely to position (p0).
Note: Rapid date and day correction is not possible between 8 p.m. and 2 a.m.
Using the chronograph / Start-Stop function
Timing a single event:
1. Press button A: the chronograph starts.
2. Press button A: the chronograph stops.
3. Press button
Note: Before you start timing, the hands should be reset to zero. If necessary, press button B.
Cumulative time function
This measures successive times. Each result is added to the previous one.
1. Press button A: the chronograph starts.
2. Press button
Repeat these two steps as many times as desired. At the end of the last measurement, the chronograph displays
the total of all the times measured. Press button
© HAMILTON 2010 – INSTRUCTION MANUAL © HAMILTON 2010 – INSTRUCTION MANUAL
3. Operating instructions
again: the chronograph stops.
A
B
completely to position (p2): the seconds hand stops.
C
nization with a time signal.
to position (p1).
C
to reset to zero.
B
again: the chronograph stops.
A
B
to reset to zero.
to reset to zero.
11