Nailer Safety Warnings - DeWalt XR li-ion DCN650 Traducido De Las Instrucciones Originales

any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the
risk of starting the power tool accidentally.
d ) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e ) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f ) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g ) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5) Battery tool use and care
a ) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
b ) Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
c ) When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
d ) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
6) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.

Nailer Safety Warnings

• Always assume that the tool contains fasteners. Careless
handling of the nailer can result in unexpected firing of
fasteners and personal injury.
• Do not point the tool towards yourself or anyone
nearby. Unexpected triggering will discharge a fastener
causing an injury.
Do not actuate the tool unless its placed firmly
•
against the workpiece. If the tool is not in contact with
the workpiece, the fastener may be deflected away from
your target.
• Disconnect the tool from the power source when the
fastener jams in the tool. While removing a jammed
fastener, the nailer may be accidentally activated if it is
plugged in.
• Do not use the tacker for fastening electrical cables. It is
not designed for installation and may damage the insulation
of electric cables thereby causing electric shock or fire hazards.
NOTE: This warning is to be provided for tackers not suitable
for fixing electric cables
Additional Finish Nailer Safety Warnings

WARNING: When using any nailer, all safety precautions,
as outlined below, should be followed to avoid the risk
of death or serious injury. Read and understand all
instructions before operating the tool.

WARNING: NEVER spray or in any other way apply
lubricants or cleaning solvents inside the tool. This can
seriously affect the life and performance of the tool.
• Do not point the tool towards yourself or anyone
nearby. Unexpected triggering will discharge the fastener
causing an injury.
• Do not use this nailer for fastening electrical cables. It is
not designed for electric cable installation and may damage
the insulation of electric cables thereby causing electric shock
or fire hazards.
• Always wear safety glasses.
• Always wear ear protection.
• Only use fasteners of the type specified in the manual.
• Do not use any stands for mounting the tool to
a support.
• Do not disassemble or block any parts of the fastener
driving tool such as the contact trip.
• Prior to each operation check that the safety and triggering
mechanism is functioning properly and that all nuts and bolts
are tight.
Do not use the tool as a hammer.
•
• Always check local workplace regulations.
• Never point any operational fastener driving tool at
yourself or at any other person.
• While working, hold the tool in such a way that no
injuries can be caused to the head or to the body in
the event of a possible recoil due to a disruption in the
energy supply or hard areas within the work piece.
• Never actuate the fastener driving tool into free space.
• In the work area, carry the tool at the workplace using
only one handle, and never with the trigger actuated.
• Consider the conditions in the work area fasteners can
penetrate thin work pieces or slip off corners and edges
of the work piece, and thus put people at risk.
Do not drive fasteners close to the edge of the
•
work piece.
• Do not drive fasteners on top of other fasteners.
EnGLIsh
29