Porter Cable 987 Manual De Instrucciones

Instruction Manual
Manuel d'utilisation
Manual de Instrucciones
Hammer Drills/Marteaux/
Drills-Drivers/Perceuse-Tournevis/
Taladro-Destornillador
®
ADVERTENCIA: Lease este instructivo antes de usarel producto.
SAVE THESE INSTRUCTIONS!
Read all instructions. Failure to follow all instructions listed below may result in elec-
tric shock, fi re and/or serious injury. The term "power tool" in all of the warnings listed below refers
to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
To reduce the risk of injury, user must read instruction manual.
GENERAL SAFETY RULES
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or
fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can
cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as
pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock. Use only 3-wire extension cords that
have 3-prong grounding-type plugs and 3-pole receptacles that accept the tool's plug.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while operating power tools may result in
serious personal injury.
b) Use safety equipment. Always wear eye protection. Safety equipment such as
dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the off-position before plugging in.
Carrying power tools with your finger on the switch or plugging in power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a
key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in
moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of these devices can reduce dust-
related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the power tools operation. If
damaged, have the power tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in accordance with these
instructions and in the manner intended for the particular type of power tool, taking
into account the working conditions and the work to be performed. Use of the power
tool for operations different from those intended could result in a hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specified by the manufacturer. A charger that is suitable
for one type of battery pack may create a risk of fire when used with another battery pack.
b) Use battery tools only with specifically designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects like paper
clips, coins, keys, nails, screws, or other small metal objects that can make a
connection from one terminal to another. Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery. Avoid contact. If
contact accidentally occurs, flush with water. If liquid contacts eyes, seek additional medical
help. Liquid ejected from the battery may cause irritation or burns.
e) Ensure the switch is in the off position before inserting battery pack. Inserting the battery
pack into power tools that have the switch on invites accidents.
6) Service
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
SPECIFIC SAFETY RULES
Wear ear protectors with drills. Exposure to noise can cause hearing loss.
Use auxiliary handles supplied with the tool. Loss of control can cause personal injury.
Hold power tools by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make
exposed metal parts of the tool "live" and shock the operator.
Verify the direction of rotation before starting the tool. Never attempt to change direction of
rotation while switch is "ON". To do so, may damage interlock feature built into switch. Be sure
switch is "OFF" and motor has completely stopped before changing direction of rotation.
Wear appropriate hearing protection during use. Under some conditions and duration
of use, noise from this product may contribute to hearing loss.
Some dust created by power sanding, sawing, grinding, drilling, and other con-
struction activities contains chemicals known to cause cancer, birth defects or other reproduc-
tive harm. Some examples of these chemicals are:
987 (1/2" 19.2V)
977 (1/2" 14.4V)
Martillos
977 model shown
with optional side handle
966 (1/2" 12.0V)
978 (1/2" 14.4V)
984 (1/2" 19.2V)
966 model shown
Cordless Drills/Drivers
Perceuse-tournevis sans fil
Taladro/Destornillador inalambrico
www.porter-cable.com
Copyright © 2006 Porter-Cable
Part No. A17592 - 03-31-06 - Rev. A
Instructivo de operacion,
centros de servicio y poliza de garantia.
• lead from lead-based paint.
• crystalline silica from bricks and cement and other masonry products.
• arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment,
such as those dust masks that are specially designed to filter out microscopic particles.
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas with soap
and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of
harmful chemicals.
Use of this tool can generate and/or disburse dust, which may cause serious and
permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from face and body.
The label on your tool may include the following symbols:
V ........... volts
Hz ......... hertz
min ....... minutes
.. direct current
....... class II tool
./min ..... revolutions per minute
IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY PACKS
The battery pack is not fully charged out of the carton. Before using the battery pack and charger,
read the safety instructions below. Then follow charging procedures outlined.
• Do not incinerate the battery pack even if it is severely damaged or is completely worn out.
The battery pack can explode in a fire.
• A small leakage of liquid from the battery pack cells may occur under extreme usage or
temperature conditions. This does not indicate a failure. However, if the outer seal is broken and
this leakage gets on your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If battery liquid gets into your eyes, flush them with clean water for a minimum of 10 minutes
and seek immediate medical attention. (Medical note: The liquid is 25-35% solution of potassium
hydroxide.)
• Charge the battery packs only in Porter-Cable chargers.
• DO NOT splash or immerse in water or other liquids.
• Do not store or use the tool and battery pack in locations where the temperature may reach
or exceed 105°F (such as outside sheds or metal buildings in summer).
• Electrocution hazard. Never attempt to open the battery pack for any reason. If bat-
tery pack case is cracked or damaged, do not insert into charger. Electric shock or electrocution
may result. Damaged battery packs should be returned to service center for recycling.
• Fire hazard. Do not store or carry battery so that metal objects can contact exposed
battery terminals. For example, do not place battery in aprons, pockets, tool boxes, product kit
boxes, drawers, etc., with loose nails, screws, keys, etc. Transporting batteries can possibly
cause fires if the battery terminals inadvertently come in contact with conductive materials such
as keys, coins, hand tools and the like. The US Department of Transportation Hazardous Material
Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e.,
packed in suitcases and carry-on luggage) UNLESS they are properly protected from short cir-
cuits. So when transporting individual batteries, make sure that the battery terminals are protected
and well insulated from materials that could contact them and cause a short circuit.
The RBRC™ Seal
The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the
nickel-cadmium battery (or battery pack) indicates that the costs to recycle the battery
(or battery pack) at the end of its useful life have already been paid by Porter-Cable. In
some areas, it is illegal to place spent nickel-cadmium batteries in the trash or munici-
pal solid waste stream and the RBRC program provides an environmentally conscious
alternative.
RBRC™ in cooperation with Porter-Cable and other battery users, has established programs in
the United States to facilitate the collection of spent nickel-cadmium batteries. Help protect our
environment and conserve natural resources by returning the spent nickel-cadmium battery to an
authorized Porter-Cable service center or to your local retailer for recycling. You may also contact
your local recycling center for information on where to drop off the spent battery.
RBRC™ is a registered trademark of the Rechargeable Battery Recycling Corporation.
IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGERS
SAVE THESE INSTRUCTIONS: This manual contains important safety instructions for battery
chargers.
• Before using charger, read all instructions and cautionary markings on charger, battery pack, and
product using battery pack.
• Electrocution hazard. 120 volts are present at charging terminals. Do not probe with
conductive objects.
• Shock hazard. Do not allow any liquid to get inside charger.
• Burn hazard. To reduce the risk of injury, charge only P
rechargeable batteries. Other types of batteries may burst causing personal injury and damage.
• Under certain conditions, with the charger plugged in to the power supply, the
exposed charging contacts inside the charger can be shorted by foreign material. Foreign materi-
als of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of
metallic particles should be kept away from charger cavities. Always unplug the charger from the
power supply when there is no battery pack in the cavity. Unplug charger before attempting to
clean.
• DO NOT attempt to charge the battery pack with any chargers other than the ones in this manual.
The charger and battery pack are specifically designed to work together.
• These chargers are not intended for any uses other than charging P
able batteries. Any other uses may result in risk of fire, electric shock or electrocution.
• Do not allow charger to get wet.
• DO NOT ABUSE CORD. Never carry charger by cord or yank to disconnect from receptacle. Pull
by plug rather than cord when disconnecting charger. This will reduce risk of damage to electric
plug and cord. Have damaged or worn power cord and strain relief replaced immediately.
• Make sure that cord is located so that it will not be stepped on, tripped over, or otherwise
subjected to damage or stress.
• Do not use an extension cord unless it is absolutely necessary. Use of improper extension
cord could result in risk of fire, electric shock, or electrocution.
• An extension cord must have adequate wire size (AWG or American Wire Gauge) for
safety. The smaller the gauge number of the wire, the greater the capacity of the cable,
that is 16 gauge has more capacity than 18 gauge. When using more than one extension
to make up the total length, be sure each individual extension contains at least the mini-
mum wire size. If an extension cord is to be used outdoors it must be marked with the suffix
W-A or W following the cord type designation. For example – SJTW-A to indicate it is acceptable
for outdoor use.
Recommended Minimum Wire Size for Extension Cords
Total Length of Cord
25 ft. 50 ft. 75 ft. 100 ft.
7.6 m 15.2 m 22.9 m 30.5 m
Wire Size AWG
18 18 16
• Do not place any object on top of charger or place the charger on a soft surface that might
block the ventilation slots and result in excessive internal heat. Place the charger in a position
away from any heat source.
• Do not operate charger with damaged cord or plug — have them replaced immediately.
• Do not operate charger if it has received a sharp blow, been dropped, or otherwise dam-
aged in any way. Take it to an authorized service center.
• Do not disassemble charger; take it to an authorized service center when service or repair is
required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.
• Disconnect the charger from the outlet before attempting any cleaning. This will reduce the
risk of electric shock. Removing the battery pack will not reduce this risk.
• NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on standard household electrical power (120 Volts). Do
not attempt to use it on any other voltage. This does not apply to the vehicular charger.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
MOTOR
Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and
voltage within plus or minus 5 percent of that shown on the specification plate on the tool. Several
models, however, are designed for A.C. current only. Refer to the specification plate on your tool for
proper voltage and current rating.
Do not operate your tool on a current on which the voltage is not within correct
limits. Do not operate tools rated A.C. only on D.C. current. To do so may seriously damage the tool.
FUNCTIONAL DESCRIPTION
FOREWORD
Your Porter-Cable Cordless Hammer Drill/Driver is designed to drill holes and drive fasteners in various
materials as indicated in the following chart. The size given is the maximum size bit or screw the drill is
designed to move through the work:
DRILLING
STEEL ALUMINUM
LO SPEED 3/8" 3/8"
HI SPEED 3/8" 3/8"
OPERATION
SWITCH OPERATION
Squeeze the trigger (A) Fig. 1 to start the motor. Release the trigger to stop the motor. As the trigger
is squeezed, the motor speed increases. NOTE: A low volume, high-pitched tone is normal while the
switch is in the variable speed mode.
FORWARD/REVERSE
• Make sure that the trigger (A) Fig. 1 is in the "OFF" position before attempting to change the direction
of rotation.
• Push the button (B) Fig. 1 toward the left side of the drill for "FORWARD" (clockwise) rotation.
• Push the button (B) Fig. 1 toward the right side of the drill for "REVERSE" (counter-clockwise)
rotation.
• Place the button (B) Fig. 1 in the center position to lock the trigger in the "OFF" position.
ELECTRIC BRAKE
When the trigger is released, an electric brake automatically engages to stop the spindle rotation.
A ...................amps
W ..................watts
or a.c. ..alternating current
n o..................no load speed
...........protective earth
rter-Cable nickel cadmium
O
rter-Cable recharge-
O
125 ft. 150 ft. 175 ft.
38.1 m 45.7 m 53.3 m
16 14 14 12
DRIVING
WOOD WOOD MASONRY
1" 3/8" -
1/2" #10 1/4"