Publicidad
Idiomas disponibles
Idiomas disponibles
Principle
The "Service" IR remote control can be
used by service personnel whenever ne-
cessary to select, start and end one of the
two test mode types, calibrate light-level
measurement and change several detect-
or parameters without using the ETS.
Parameters changed by IR remote control
are then automatically sent by bus and
can also be read on the bus at any time if
this function is enabled by means of the
relevant ETS setting.
Note: To start a test mode or change a
parameter with the IR remote control, the
detector's service mode must always be
switched 'ON' by IR remote control first.
Any reception of an IR signal is acknowl-
edged by the blue LED flashing in the de-
tector.
The LED flashes for approx. 2 s if the de-
tector evaluates a value entered as being
permissible and adopts it. If the value en-
tered is incorrect, the LED flashes rapidly
for approx. 2 s. The value entered is re-
jected and the input process must be
completely repeated.
–
On accidentally entering more than four
digits, the relevant button (e.g. Set Lux)
must be pressed again and the value then
Functions
>2s
1
Unlocking/locking, service mode
–
Press "
" button for approx. > 2 s until
x
IQ
the blue LED flashes for approx. 2 s on
min
the detector. Pressing the button for sev-
eral moments ensures that any brief actu-
ation of this button does not immediately
S
–
H
E
Norm
result in the service mode being activat-
F
N
S
ed. The detector only evaluates further IR
signals received if the service mode is
switched 'ON'. This ensures that any
Cal.
Set
inadvertent actuation of a button on the
Lux
Lux
remote control does not immediately
result in a parameter change.
Test
entered on the number pad.
The following functions can be performed
using the RC 6 service remote control:
1
Unlocking/locking, service mode
2
Reach, sensor sensitivity (HF only)
3
Light level, brightness setting, teach-in
4
Lighting control stay-'ON' time,
IQ mode
5
HVAC switch-'ON' delay,
room surveillance,
HVAC stay-'ON' time
6
Basic illumination 'ON' period,
brightness setting, teach-in
7
Presence and lighting test mode
8
Number pad/"OK"
–
–
Press "
" button for approx. > 2 s until
the blue LED flashes for approx. 2 s on
the detector. If this is not done, service
mode is automatically terminated by the
detector if it receives no further IR signal
x
x min
within 10 minutes of receiving the last
Delay
min
one.
Note:
x
Terminating the service mode does not
Set
min
Lux
terminate any detector test mode
0-50%
activated.
–
1
0
Ok
8
x
IQ
Cal.
Set
min
Lux
Functions
Lux
S
2
–
8
Test
+
H
E
Norm
F
N
S
>2s
Reach
–
Briefly press "
", set the chosen value
Cal.
Set
Lux
Lux
on the number pad, pressing "OK" to
>2s
x
confirm.
IQ
min
Test
The following scale applies:
1 = very large movements are detected,
x
S
–
2 = large movements are detected,
IQ
H
E
Norm
min
F
N
3 = moderate movements are detected,
S
4 = minor movements are detected.
S
–
H
Cal.
Set
E
Norm
F
N
Lux
Lux
S
3
8
Test
Cal.
+
Set
Lux
Lux
Light level
Test
Whenever possible, light-level measure-
ment should be calibrated with daylight
shut out, i.e. ideally when it is dark, how-
ever at least with roller shutters or blinds
down. The lighting must be switched 'ON'
completely or dimmed up to max. output.
Below the presence detector, stand a
table with a surface providing a level of
reflection equivalent to that of the later
work surface. Using a calibrated luxmeter,
measure the light intensity on this table,
wherever possible directly below the
presence detector. The lux level measured
must then be sent to the detector by
remote control. If the lux level measured
is outside the detector's light-level meas-
uring range of 10 to 1500 lux, lighting
must be dimmed down until the lux level
measured falls within the measurement
range.
x
Set
min
Lux
0-50%
–
x
x min
1
0
Ok
Delay
min
Sensor sensitivity (HF)
x
The HF-detector's sensitivity can either
Set
min
Lux
be set to "High" or "Low". "High sensitiv-
0-50%
ity" responds to any movement detected.
"Low sensitivity" only responds after de-
–
1
tecting several movements.
0
Ok
- "High": Briefly press "Norm" button.
x
x min
- "Low": Briefly press "–" button.
Delay
min
Fernbedienung
x
x
x min
Set
Delay
min
min
Lux
RC6 KNX PROGRAMM
0-50%
–
x
Set
1
0
Ok
min
Lux
0-50%
Transmitting lux level
Fernbedienung
–
To transmit the measured lux level to the
1
0
Ok
RC6 KNX PROGRAMM
detector, press "Cal. Lux", enter the
measured lux level on the number pad,
pressing "OK" to confirm.
Note:
–
After entering the last digit, wait for ap-
prox. 5 seconds before pressing the "OK"
button.
Fernbedienung
RC6 KNX PROGRAMM
Brightness setting
The setting for controlling light level can
be adjusted within a range of 10 to 1000
Fernbedienung
lux.
RC6 KNX PROGRAMM
- Briefly press "Set Lux" button, enter lux
level on the key pad, pressing "OK" to
confirm.
–
Teach-in
The "
" button must be pressed at the
level of light at which you want the
detector to respond to movement from
now on. The current twilight value is
saved.
9
Publicidad
