STEINEL Presence Control PRO RC 6 Manual De Instrucciones página 6

>2s
>2s
x
. Set
x Lux
Functions min
x
4 8
+
x
IQ 1
IQ
min
min
Lighting control stay-'ON' time
The lighting stay-'ON' time can either be
S
–
S
H – E
Norm
set to a fixed period of between 1 and
H E
F
Norm N
F N
S
30 minutes or is automatically matched in S
"IQ mode" to the time persons spend in
the detection zone.
Cal. Set
Cal. Set
Lux Lux
Lux Lux
Test
5 x
Test
x min +
Delay min
Fernbedienung
HVAC switch-'ON' delay
RC6 KNX PROGRAMM
The switch-'ON' delay for controlling >2s
x
Set
HVAC can either be set to a fixed period
Lux
min
0-50%
of between 1 and 30 minutes or is auto-
matically matched in the "Room surveil-
lance" mode to the time persons spend in –
x
1
0 Ok
IQ
the detection zone.
min
- Fixed time:
Briefly press "x min Delay", enter the
chosen time on the number pad; press
S
–
H E
Norm
"OK" to confirm. F
N
S
- Room surveillance:
Briefly press " " button.
x
x min
Cal. Set
Delay min
Lux Lux
x
6
Test
Set +
min Lux
0-50%
Fernbedienung
Basic illumination 'ON' period
RC6 KNX PROGRAMM
The basic illumination 'ON' period can be –
1 0
Ok
set to a duration in the range of 1 to 30
minutes.
- Briefly press "x min" button, enter the
chosen time on the number pad, pressing
"OK" to confirm.
'ON' period for selected brightness
setting
The basic light-level threshold can be
adjusted within a range of 10 to 300 lux.
- Briefly press "Set Lux", enter the
chosen value on the number pad,
pressing "OK" to confirm.
Fernbedienung
RC6 KNX PROGRAMM
Set
Lux
0-50%
–
0 Ok
- Fixed time: Briefly press "x min" button,
x
x min
x
x min enter the chosen time on the number
Delay min
Delay min
pad and press "OK" to confirm.
- In the IQ mode the stay-'ON' time auto-
matically and dynamically adjusts to
x
Set
x
Set
user behaviour. Briefly press "IQ" button.
min Lux
min Lux
0-50%
0-50%
–
8 – 1 0
Ok
1 0
Ok
HVAC stay-'ON' time
The HVAC stay-'ON' time can be set
to a fixed period of between 1 and
120 minutes.
- Briefly press "x min" button, enter
the chosen time on the number pad,
pressing "OK" to confirm.
x
x min
Delay min
Fernbedienung
Fernbedienung
RC6 KNX PROGRAMM
RC6 KNX PROGRAMM
x
Set
min Lux
0-50%
8 –
1 0
Ok
Teach-in
Pressing the " " button enters current
light level as the threshold for basic
brightness.
Note: To do this, the "Basic illumination
'ON'" parameter must be set to
"in relation to light level" (see 11.9.
p. 18 Calibration description).
www.knx.steinel.de
Fernbedienung
RC6 KNX PROGRAMM
10
Cal. Set
Lux Lux
Functions
7
Test
Test
Presence test mode:
"Presence test mode" is used for check-
ing the detection zone. Any movement
detected results in brief flashing of the
blue LED. Communication objects are not
sent during the presence test mode.
Lighting test mode
"Lighting test mode" is used for checking
light-level control. To do this, the detector
must have been parameterised by ETS
and its objects linked with the objects of
the buttons and actuators for lighting
control. In this test mode, any movement
detected results in brief flashing of the
blue LED. For the duration of this test
mode and irrespective of the parameters
selected for the presence detectors, light-
–
level control and remote control are acti-
vated for both types of IR remote control,
with lighting control stay-'ON' time being
set to 5 s. The "presence detection" and
"HVAC control" functions are deactivated.
The associated objects are not sent. The
presence detector is re-started after ter-
–
x
Set
Cal. Set
min Lux
Lux Lux
0-50%
8 –
+
1 0
Ok
Fernbedienung
Fernbedienung
RC6 KNX PROGRAMM
RC6 KNX PROGRAMM
11
x
Set
min Lux
0-50%
–
1 0
Ok
- Activate presence test mode:
Briefly press "Test", then briefly press
"1" followed by "OK".
- Terminate presence test mode:
Briefly press "Test", then briefly press
"1" followed by "OK".
minating the lighting test mode. Any
parameters changed at the beginning of
the test mode are now reset to the values
selected with ETS.
- Activate "lighting test mode":
Briefly press "Test", then briefly press
"2" followed by "OK".
- Terminate "lighting test mode":
Briefly press "Test", then briefly press
"2" followed by "OK".