Cleaning And Storage - Masterpro BGMP-9127 Manual De Instrucciones

EN
13. To switch off the device, move the On / Off switch to position 0 and pull the mains plug out of
the plug socket.
14. Carefully remove the lid.
15. Twist the steaming attachment anticlockwise until the tab is released and carefully lift it off
(follow the instructions provided in "Using Accessories Correctly" | "Steaming Attachment").
16. Carefully remove the mixing bowl from the motor unit and pour away the hot liquid.
• Using the Weighing Function
Make sure that the device is positioned stably on a flat work surface and the suction feet
stick to it properly so that the scale can display the most accurate measurement results
possible.
How to use this function? Please follow the below steps:
1. Switch on the motor unit by flipping the On / Off switch on the back of the motor unit to the I
position.
2. Press the POWER button to activate the device.
3. Press the WEIGHING FUNCTION button to activate the weighing function.
The preset unit of measurement is grams. You can change the unit of measurement by
repeatedly pressing the WEIGHING FUNCTION button (grams / kilograms (g / kg) –
pounds (lb) – ounces (oz)).
4. Place the ingredient to be weighed onto the scale. The weight is displayed.
5. If the WEIGHING FUNCTION button is pressed and held for approx. 3 seconds, the Tare
Function (Tare) is activated and the weight displayed is reset to 0, further ingredients can be
weighed.

CLEANING AND STORAGE

• CAUTION!! Risk of burns! Allow the device to cool down completely before cleaning it.
• CAUTION!! Danger of electric shock from water! Remove the mains plug from the
plug socket before cleaning the device.
• CAUTION!! Risk of damage to the device! Do not immerse the motor unit and mixing
bowl in water or any other liquids.No liquid must get into the bottom section of the mixing
bowl as this is where heating elements and other electronic components are fitted. The
mixing bowl must not be cleaned in the dishwasher.
• The device and all its accessories are not dishwasher-safe!
• Clean the mixing bowl and the accessories immediately after each use to prevent germ formation.
Do not allow food residues to dry on.
• Do not use any corrosive or abrasive cleaning agents or scouring sponges to clean the device.
These can damage the surface.
Please follow the below steps for cleaning and storage:
1. Rinse out the inside of mixing bowl briefly under running water.
• If the mixing bowl and cross-blade attachment are only slightly dirty, it is sufficient to
clean them briefly using water:
1) pour 1 litre of water and a few drops of washing-up liquid into the mixing bowl,
2) close the mixing bowl with the mixing bowl lid including the measuring cup,
3) press the PULSE FUNCTION button a few times,
4) rinse out the mixing bowl thoroughly with clear water.
14
• If the mixing bowl inside need to be cleaned with cloth by hands, don't forget to use the blade cover
to protect your hands from hurts (follow the instructions provided in "Using Accessories Correctly" |
"Blade Cover").
2. Wash all of the accessories in warm, soapy water. If necessary, remove the cross-blade
attachment from the mixing bowl for cleaning (follow the instructions provided in "Using
Accessories Correctly" | "Cross-Blade Attachment").
WARNING: Handle the cross-blade attachment with care as the blades are extremely sharp.
3. If necessary, remove the sealing rings for cleaning.
4. Wipe down the motor unit with a slightly damp cloth if necessary and then dry it with a soft
cloth.
5. Allow all parts to dry completely before the device is reassembled.
6. Reattach all sealing rings (follow the instructions provided in "Using Accessories Correctly" |
"Mixing Bowl Lid" and "Steaming Attachment").
7. Store the device in a dry, clean place that is not accessible to children and animals.
The plastic parts may suffer discolouration over time. However, this does not have any
negative effect on either health or the way that the device parts work.
15
EN