General Information - Hozelock Biomix Manual Del Usuario

GB

General Information

• Please follow the instructions carefully to get the best results
from your Biomix plant fertiliser maker.
• Use protective clothing to prevent unwanted staining.
• Do not allow Children and Pets to go near the Biomix.
• This product is designed for outdoor use only!
• An outdoor location in your garden between 12°C and 25°C
will perform best.
• Protect your Biomix from heavy rainfall.
• This product is not for supplying food or liquids
for human consumption.
• Plastic tap nuts are suitable for hand tightening only
– Avoid using a spanner because it could damage parts.
• This product can utilise water from an outdoor water
butt or tank.
This product is not designed to be used freezing
(frost) temperatures. During the winter drain
all water from your Biomix and store it indoors
in your garage or shed until the next Spring Season.
To remove the Solids Bucket from the Filter Frame: Stand on
the the filter frame and pull the empty bucket upwards (See Fig 2).
Before first use
Ensure that the tap (Fig 1.A) has been fitted securely onto the
main vessel (Fig 1.B). Remove the solids bucket and filter (Fig1.
G+H+J) from the main vessel and fill the vessel with 10 litres
of water. Allow water to stand for 10 minutes and check that
no water has leaked from the tap. If some water has escaped
remove the water and check the nut is securely tightened on
the inside. The nut needs to be tight enough so that the knob
can be opened and closed and the tap body remains secure.
If the nut is secure but continues to leak, remove the tap and
check the seals and the area around the hole is not damaged.
Remove any debris from the seal surfaces then reassemble the
tap.
Instructions for using the BioMix
FIG.8
Note items Fig1.G+H+J are preassembled ready for first use.
8A
To assemble these items place the filter mesh (Fig1.J) into
the Filter Frame (Fig1.H) then fit the Solids Bucket (Fig1.G)
onto the filter frame. The four snap legs align with the four
slots on the base of the Solids Bucket (Fig1.G).
Fill the Solids Bucket with 1 Kg your chosen plant material.
8B
Refer to the recipes for best results. Cut it into 5cm (2 inch)
pieces, or smaller. For dried pellets refer to the recipe for
weights. Use gloves when handling plant material because
some plants may sting or urticate. Make sure that no plant
material falls into the main vessel (Fig1.B).
Put the Solids Bucket assembly (Fig1.G+H+J) inside the
8C
Main Vessel (Fig1.B). Add 10 Litres of rainwater (Use the
top of the four internal ribs as a level guide). Pull the leaves
back to check the water level (Fig 4). Rain water from a
water butt is best. If using tap water leave it outside for 24
hours to allow the added fluoride/chlorine to disperse
Add the lid assembly (Fig1.D). Move the fingers back
8D
and forth as you push the fingers down will help to push
through.
Leave the mixture for 48 hours before turning the mixing
8E
handle for the first time. This allows the leaves and stems to
soften in the water. Give the mixture a stir every day, or two
days. Refer to the recipes for the durations.
Use the viewing window to check the mixture. For some
8F
recipes you know when the maceration is complete and
the plant fertiliser is ready when bubbles stop rising to the
surface. Condensation may appear on the inside surface
of the window when the temperature is warmer inside the
Biomix. Tapping on the window or rotating the handle
quickly can help to remove the droplets. If the droplets
cannot be removed then lift off the lid and wipe away the
droplets with a tissue. Direct sunlight on the Biomix lid and
airflow over it will help reduce condensation.
Lift off the lid assembly slowly so that the liquid can run off
8G
the fingers back into the bucket.
When ready slowly lift the Solids Bucket assembly (Fig1.
8H
G+H+J) turn it 45 degrees, and place it on top of the main
vessel to filter. Plant materials will break down into small
particles and slime. The filtering process can take between
15minutes and 2 hours depending on the plant material
used. To speed it up use a long, soft spatula to carefully
scrape the filter material to reveal a clean area that will
allow the draining process to continue.
When draining is complete the remaining solids in the
8I
Solids Bucket can be discarded onto your compost heap.
Used plants can help to speed up the decomposition
process in your compost heap!
Empty the liquid from the main vessel into a glass jar or
8J
plastic bottle that has a lid that can seal tight. Do not
use metal containers to store your plant fertiliser. Store it
away from children and pets. If you intend to store it for a
long time filter the liquid through the filter bag supplied to
remove any plant leaves and store it in a dark, dry location.
For sprayers and other applicators with fine holes it is
8K
important to use the fine filter bag (Fig1L). After use the
filter bag can be washed clean before using it again. Dilute
the plant fertiliser in the ratio stated in the recipe lists.
8L
Scrape off the sediment inside the bottom of the Solids
Bucket. Use a soft spatula being careful not to damage the
filter mesh (Fig1.J) and wash with water. You can remove
the filter mesh from the filter frame and rinse it under a tap.
Technical Data
Liquid Volume = 10 Litres to top of ribs. This will vary depending
on the density of the plant material placed inside the Solid
bucket.
Fig. 9.A This area allows room for foaming (frothing) as the
plant fertiliser is brewing.
Fig. 9.B 10 Litres of water is approximately the height of the
internal ribs. (Fig. 9C). Height may vary depending on the plant
material being used.