Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Assembly & Installation Instructions
CAUTION:
Read instructions carefully and turn electricity off at main circuit breaker panel before beginning
installation.
WARNING: Follow the instructions carefully to assure full compliance with local, state, and NEC requirements. If there are any
questions, contact a Qualified Electrical Contractor.
WARNING: Risk of fire or electrical shock. Install this kit only in 4" Junction Boxes per the dimensions shown.
WARNING: To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
CAUTION: Risk of fire. Consult a Qualified Electrician to ensure correct branch circuit conductor.
NOTE: This product is designed to operate with most standard incandescent or low voltage electronic dimmer switches. Results
may vary. For recommended dimmers, consult product specification sheet for more details.
NOTE: SUITABLE FOR WET LOCATIONS IN COVERED CEILINGS
WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects and/or other
reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.
NOTE: Always install with ambient temperatures specified on the product specification sheet. 5 year warranty.
See www.progresslighting.com for details.
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PTODUCT AND THE HAZARDS INVOLVED.
1. Mount the bracket to the junction box with two screws.
2. Connect wires as noted and shown.
3. Always attach the ground wire to the screw on the bracket.
4. Align the wire spring clips with center hole in the bracket and push until the unit snaps into place. If the unit does not snap into place,
make sure junction box and bracket are flush with the ceiling.
KEEP THESE INSTRUCTIONS
P8240, P8241, P8222, P8247 & P8147 SERIES
BRACKET
Page 1 of 6
1/2" MINIMUM JUNCTION BOX DEPTH
4" JUNCTION BOX
GROUND
SCREW
TRIM SHAPE
MAY VARY.
SPRING
CLIPS
SPEC. NO. 93054065 2-22-16
Publicidad
Manuales relacionados para Progress Lighting P8240 Serie
Resumen de contenidos para Progress Lighting P8240 Serie
- Página 1 P8240, P8241, P8222, P8247 & P8147 SERIES Assembly & Installation Instructions CAUTION: Read instructions carefully and turn electricity off at main circuit breaker panel before beginning installation. WARNING: Follow the instructions carefully to assure full compliance with local, state, and NEC requirements. If there are any questions, contact a Qualified Electrical Contractor.
- Página 2 WARNING: Risk of fire or electric shock. Do not alter, relocate or remove wiring, lampholders, power supply or any other electrical component. WARNING: Risk of fire or electric shock. LED retrofit kit installation requires knowledge of the construction and operation of the luminaires’ electrical systems and the hazard involved. If not qualified, do not attempt installation.
- Página 3 SÉRIE P8240, P8241, P8222, P8247 & P8147 Instructions d’assemblage et d’installation ATTENTION : Lire les instructions avec attention et couper l’électricité au niveau du tableau électrique principal avant de procéder à l’installation. AVERTISSEMENT : Suivre les instructions avec attention pour assurer la pleine conformité aux normes locales, provinciales et nationales en vigueur.
- Página 4 AVERTISSEMENT : Risque d’incendie ou de choc électrique. Ne pas modifier, déplacer ni retirer de câblages, douilles de lampe, alimentation électrique ou autre composant électrique. AVERTISSEMENT : Risque d’incendie ou de choc électrique. L’installation du nécessaire de remplacement à DEL suppose une bonne connaissance de la configuration et du fonctionnement des systèmes électriques des luminaires et des danger associés.
-
Página 5: Instrucciones De Ensamblaje E Instalación
SERIES P8240, P8241, P8222, P8247 & P8147 Instrucciones de ensamblaje e instalación PRECAUCIÓN: Lea atentamente las instrucciones y corte la electricidad desde el panel principal de disyuntores antes de comenzar la instalación. ADVERTENCIA: Siga las instrucciones atentamente para garantizar el cumplimiento total de los requisitos locales, estatales y de NEC. Si tiene preguntas, comuníquese con un contratista de electricidad calificado. - Página 6 ADVERTENCIA: Riesgo de incendio o descarga eléctrica. No altere, reubique ni retire el cableado, los portalámparas, el suministro de energía ni ningún otro componente eléctrico. ADVERTENCIA: Riesgo de incendio o descarga eléctrica. La instalación del juego de modernización LED requiere conocimiento de la construcción y funcionamiento de los sistemas eléctricos de las luminarias y los peligros que implican.