Cequent Performance Products 75772 Instrucciones De Instalación

Frame rail
Hitch Shown In Proper Position
Equipment Required: #2 Phillips Screwdriver
Fastener Kit: 75772F
Wrenches: 17mm, 19mm
Drill Bits: None
Cut Down at Radius
2"
Figure 2
j
Qty. (4) M12 x 1.75 x 120 Bolt CL8.8
k
1/2" Conical Washer
Qty. (8)
l
Qty. (4) M12 x 1.75 Nut CL10
1. Lower and remove spare tire from vehicle. The tire release is located underneath the storage compartment in the back of the vehicle.
2. Remove the driver side rear plastic cover, located underneath the vehicle, by using a #2 Phillips head screwdriver to remove fasteners, also remove
(4) plastic push pins. Then remove the passenger side rear plastic cover, located underneath the vehicle, by removing fasteners, and (3) plastic push
pins (Do not discard items).
3. Lower exhaust by removing the rear and side hangers.
4. Raise hitch into position and insert M12 bolts through the bracket and frame as shown in Figure 1. Note: The bumper locator pin may interfere
with the hitch hardware. If necessary, use an angle grinder to trim the locator pin at the shoulder to allow proper hardware clearance.
5. Insert M10 bolts through bracket and into the frame as shown in Figure 1 (Hand tighten).
6. Torque M10 bolts first and then M12 bolts to the specifications below.
7. Reinstall exhaust hangers into mounts.
8. Trim rear plastic covers as shown in Figure 2, then raise into position, reinstall the fasteners and push pins that were removed in Step 2.
9. Reinstall spare tire and make sure it is seated properly.
Tighten all M10 CL10.9 fasteners with torque wrench to 40 Lb.-Ft. (54 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2013 Cequent Performance Products, Inc.
Installation Instructions
Hyundai Santa Fe Sport (5 Passenger)
Fascia
jkkl
2 Existing Weld Nuts
(Typical)
CONSULT WITH VEHICLE OWNER BEFORE CUTTING REAR PLASTIC COVERS
Kia Sorento
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
Fasteners typical both sides
mn
Figure 1
m
Qty. (4) M10 x 1.25 x 30 Bolt CL10.9
n
7/16" Conical Washer
Qty. (4)
o
Qty. (1) Spacer Plate
Tighten all M12 CL8.8 fasteners with torque wrench to 72 Lb.-Ft. (98 N*M)
Sheet 1 of 3 75772N
Part Numbers:
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
5250 Lb (2381 Kg)
3500 Lb (1587 Kg)
Accessory Rating
o
Spacer Plate
4-24-13
75772
44689
87634
Max Tongue
WT (LB)
525 Lb (238 Kg)
525 Lb (238 Kg)
C
Rev. B
Form: F205 Rev C 9-17-2012