Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Truck frame
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75740F
Wrenches: 3/4", 7/8"
Drill Bits: None
All Fasteners Typical
Both Sides
1
Qty. (6)
1/2"-13 X 1-3/4" Carriage Bolt Gr5
2
Qty. (6)
1/4" x 1-1/2" x 2" Block with square hole
3
Qty. (6)
½" Flat Washer
1.
Before installing hitch lower spare tire on all SuperDuty trucks. Lower spare tire on all Light Duty trucks with 16" or larger tires.
Spare will be relocated or reinstalled after hitch installation.
Note! - 20" spare tires will not allow original relocation under truck.
2.
Make sure that no electrical wires or other obstructions are inside of truck frame so that bolts and blocks can sit flat on bottom of
frame when tightened in the following steps.
3.
Install carriage bolts and blocks down through truck frame as shown in Figure 1. Raise hitch into position carefully so as not to
push bolts back through frame. Loosely install flat washers, lock washers and hex nuts onto carriage bolts. After ensuring that
blocks and bolts are sitting flat, torque bolts to 75 Lb.-Ft. (102 N*M).
4.
Reinstall spare tire. Note: Spare tire may have to be relocated.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of
water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye
protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
z
2012 Cequent Performance Products, Inc.
Installation Instructions
99-2007 Ford F250/350 Superduty Truck
97-2003 Ford F150 & F250 LightDuty Truck
2004 Ford F150 Heritage Truck
*See notes below regarding spare tire
Bumper
Tighten all 1/2-13 Gr5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Do Not Exceed Lower of Towing Vehicle Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU1, PU2 --- PU3 on 04' Heritage
1
2
3
4
5
Figure 1.
4
Qty. (6)
1/2" Helical lock washer
5
Qty. (6)
1/2" Hex Nut
Sheet 1 of 3
75740N
Part Numbers:
75740
87618
44673
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
10,000 (4540 Kg)
1000 (454 Kg)
6000 (2724 Kg)
900 (408 Kg)
2-14-12
Form: F205 Rev A 5-6-05
Rev. A
Publicidad
Manuales relacionados para Cequent Performance Products 75740
Resumen de contenidos para Cequent Performance Products 75740
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75740N 2-14-12 Rev. A 2012 Cequent Performance Products, Inc. Form: F205 Rev A 5-6-05...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75740N 2-14-12 Rev. A 2012 Cequent Performance Products, Inc. Form: F205 Rev A 5-6-05...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 75740N 2-14-12 Rev. A 2012 Cequent Performance Products, Inc. Form: F205 Rev A 5-6-05...