Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 01131-100
Wrenches: 3/4, 13/16, 7/8
Drill Bits: 9/16
Existing on 8' Bed
Drilled on Pre-1999
Model 6-1/2' Bed
Crossmember & Rivet
Location Varies by Model
j
Hex Bolt – 9/16-18 x 2.00 GR5
Qty. (8)
k
Spacer – ¼ x 1-1/2 x 2
Qty. (4)
l
Flanged Locknut – 9/16-18
Qty. (8)
m
Flat Washer (Hardened) – 9/16"
Qty. (2)
*Reinforcement bracket (Item 7) is for driver's side of vehicle (not shown).
1.
If needed, enlarge existing 12mm (.47) holes in frame to 9/16 (.56).
2.
Remove bumper bolt strap and bolt from bumper frame assembly, one side only.
3.
Cut bolt strap in half as shown in figure 2. Loosely reinstall bumper fasteners and reinforcement bracket inside frame.
4.
Repeat steps 1 & 2 on opposite side of vehicle.
5.
Insert hex bolt (Item 1) and hardened flat washer (Item 4) in first attachment holes in each frame rail as shown in Figure 1.
6.
Insert hex bolt (Item 1) and spacer (Item 5) in forward attachment holes in each frame rail as shown in Figure 1.
7.
Raise hitch into position and loosely attach fasteners to bolts as shown in Figure 1.
8.
Center hitch and install remaining fasteners as shown in Figure 1.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
1998, 2006, 2012 Cequent Performance Products
Installation Instructions
Dodge Ram Pickup Truck
Step Bumper
jnl
Frame Rail
Bumper
Bracket
Tighten all 9/16 GR5 fasteners with torque wrench to 110 Lb.-Ft. (149 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU1, PU2
jkl
Existing Bolt Strap (Modified-See Figure 2)
Reinstalled in Rearmost Lower Hole Thru
Frame and Bumper Bracket
'94 Model
'95 & Later Models
Existing Fasteners
jmop*l
Figure 1
n
Spacer – 3/8 x 1-1/2 x 3
Qty. (2)
o
Qty. (1)
Reinforcement Bracket
p
Qty. (1)
Reinforcement Bracket
Sheet 1 of 3
N41923
Part Numbers:
41923
96923
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
14,000 (6356 Kg)
1,400 (636 Kg)
12,000 (5448 Kg)
1,200 (545 Kg)
Note: All Fasteners Typical
Both Sides of Vehicle
Figure 2
Bolt Strap Modification
6-1-12
Form: F205 Rev A 5-6-05
Cut Here
Rev. B
Publicidad
Manuales relacionados para Cequent Performance Products 41923
Resumen de contenidos para Cequent Performance Products 41923
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 1998, 2006, 2012 Cequent Performance Products Sheet 1 of 3 N41923 6-1-12 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 1998, 2006, 2012 Cequent Performance Products Feuille 2 de 3...
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684 1998, 2006, 2012 Cequent Performance Products Hoja 3 de 3 N41923 6-1-12 Rev.