Cequent Performance Products 41942 Instrucciones De Instalación

Vehicle
Frame
Bumper
Spring shackle
Hitch Shown In Proper Position
(Shown on short bed with bolt-on bracket)
Equipment Required:
Fastener Kit: 41942F
Wrenches: 13mm, 21mm, 22mm, 3/4", 7/8"
Drill Bits: None
Other items: Plastic cutting tool,
(short bed as needed. (heat shield)
(2) Bolt-on brackets supplied. Use on
short-bed trucks only. Same bracket
just rotate for other side.
Passenger's side
Driver's side
See next page for detail on
short-bed trucks.
Qty. (6) Hex Bolt, M14 x 2.0 x 45mm CL10.9
1
Conical Toothed Washer, 5/8" (black color)
Qty. (6)
2
Hex Bolt, 1/2"-13 x 1-1/2" Gr.5 (shortbed only)
Qty. (4)
3
Conical Toothed Washer, 1/2" (gold color)
Qty.(8)
4
1. Lower spare tire from underneath of truck for ease of installation. Also remove existing 14mm bolts from end of each truck frame rail. Return bolts to vehicle
owner. If truck has existing hitch remove bumper bolts also.
On short bed trucks, remove rearmost 8mm bolt holding plastic heat shield to bottom of frame on passenger's side. See picture 1. next page.
2.
3. For short bed trucks, attach bolt-on brackets supplied with hitch to hitch brackets as shown above. Torque to specs below.
For long-bed trucks, discard bolt-on brackets or give to vehicle owner explaining that they are not needed for 8' bed applications.
4.
5. Raise hitch into position locating slots in hitch over existing weldnuts in truck bumper and end of truck frame rails.
6. For short-bed trucks sandwich tab of plastic heat shield between hitch and frame underneath on passenger side of truck. In some cases it may be necessary to
trim plastic gusset on heat shield to allow shield to stay in place. See picture next page.
7. Install supplied 14mm bolts and conical toothed washers into existing weldnuts as shown above and torque to 115 Lb.-Ft. (156 N*M).
8. On forward attachments install supplied M14 bolts and flat washers through access hole on inside or outside of frame and down through slots in bottom of
truck frame and hitch. Attach nuts and conical toothed washers to forward bolts both sides and torque to 110 Lb.-Ft. (136 N*M).
9. Raise spare tire back into place.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2010, 2012 Cequent Performance Products
Installation Instructions
GMC Sierra/Chevrolet Silverado 2500 & 3500 HD Pickups.
(All inc. Regular, Crew, Extended & Dually - 2 & 4WD Long & Short-bed)
GMC Denali HD Crew-Cab Pickup.
Bumper
Fascia
Figure 1.
2
8
This side shows
long-bed configuration,
do not use bolt-on
brackets.
Tighten 1/2"-13 Gr.5 bolts with torque wrench to 75 Lb.-Ft. (102 N*M)
Do Not Exceed Lower of Towing Vehicle Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3
This side shows
short-bed
configuration
7
1
*3
*4
*Universal bolt-on
bracket, use on
short-bed only.
Typical both sides
2
1
Hex Nut, 1/2"-13
Qty. (4)
5
0
Block, 1-1/2" x 2" with round hole (shortbed only)
Qty. (2)
6
Flat Washer, 9/16"
Qty. (3)
7
Qty. (2) Hex Nut, M14 x 2.0
8
Sheet 1 of 6 41942N
Part Numbers:
Max Gross
Trailer WT (LB)
16,000 (7264 Kg)
15,000 (6810 Kg)
*6
1
attachment,
14mm weldnuts
2
1
6-1-12
Form: F205 Rev A 5-6-05
41942
96942
Max Tongue
WT (LB)
1600 (726 Kg)
1500 (681 Kg)
*4
*5
1
Frame
attachment
14mm
weldnuts
2
Bumper
Rev. B