Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame
Hitch Shown In Proper Position
Equipment Required: Pull wire (provided)
Fastener Kit: 75730F
Wrenches: 7/8" & 18mm
Existing bolts
Both sides
Qty. (4)
Carriage Bolts 1/2-13 X 2.00 Gr5
Qty. (4)
Spacers ¼ X 1.50 X 2.00
1.
Remove the bolts that hold the bumper in place, being careful not to drop the bumper.
2.
Lower the bumper and remove the bumper support bolts and bracket from the frame rail. Return brackets to owner to reinstall if
hitch is removed. Fasteners to be re-installed .
3.
Raise hitch into place and re-install bolts (removed in step 2) into the weldnuts located on the frame, where the bumper support
brackets were removed.
4.
Using the pullwire insert the spacers and carriage bolts into the frame and into the holes in the bottom of the frame as shown.
5.
Remove pull wires and install conical washer and hex nuts as shown.
6.
Re-install the bumper at the rearward slots on the bracket using the remaining bolts removed in step 1.
7.
Torque all fasteners to specification.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
©
2011 Cequent Performance Products
Installation Instructions
Bumper
Existing weldnuts
Bumper
Tighten all 1/2" fasteners with torque wrench to 75 Lb.-Ft. (102 n*m)
Tighten all existing M12 fasteners with torque wrench to 75 Lb.-Ft. (102 n*m)
Toyota Hilux
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3 & PU4
Existing hole
Example of pull wire procedure
Qty. (4)
Conical washer ½"
Qty. (4)
Hex Nut 1/2-13
Sheet 1 of 3
Part Numbers:
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
9,000 (4086 Kg)
6,000 (2724 Kg)
Note: Fasteners typical
both sides
Kink pull wire to keep block
independent of bolt
75730N
9-9-11
Form: F205 Rev A 5-6-05
75730
Max Tongue
WT (LB)
900 (409 Kg)
900 (409 Kg)
Frame
Rev. A
Publicidad
Manuales relacionados para Cequent Performance Products 75730
Resumen de contenidos para Cequent Performance Products 75730
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2011 Cequent Performance Products Sheet 1 of 3 75730N 9-9-11 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. ©2011 Cequent Performance Products Feuille 2 de 3 75730N 9-9-11 Rev.
- Página 3 Números de partes: Instrucciones de instalación Bastidor 75730 Toyota Hilux Parachoques No supere el valor inferior entre la calificación del fabricante del vehículo de remolque o Peso máximo bruto Peso máximo Tipo de enganche del remolque (LB) (LB) 9.000 (4086 Kg) 900 (409 Kg) Distribución de peso...