DeWalt DW7464 Manual De Instrucciones página 9

Secure the side of the 52" rail table to the front rail
brackets using the two M8 x 20 carriage bolts, 10mm flat
washers, 8mm lock washers and nuts. Finger tighten.
Attach 52" rail table to the support bracket (Fig. 15)
using the M10 x 25 bolts. Secure each bolt with a flat
washer, lock washer, and nut. Tighten snug only.
FIG. 14
M10 WASHER
FIG. 15
STEP 21. Attach lower support rails.
You will need: 4 - 8mm carriage bolts
4 - 8mm flat washers
4 - 8mm lock washers
4 - 8mm nuts
Attach lower support rails between the bottom of the
support pan and the right cross member (Fig. 16) with
four M8 x 20 carriage bolts. Secure each bolt with a flat
washer, lock washer, and nut. Tighten securely.
NOTE: If you are installing the 52" Fence System with
a Mobile Base, insure the adjustable rubber feet are
adjusted all the way up into the Mobile Base, and
insure the cast iron feet on the table saw legs are seat-
ed against the legs.
STEP 22. Parallel 52" rail table to the saw table top.
Table should be level with the table saw top. For the
edge closest to the saw table use your fence face or a
straightedge to extend the saw table surface over the
rail table. To align the tables tap on the rail table with a
soft hammer or a regular hammer and a block of wood
until they are even. Tighten the M10 hardware through
the support bracket (Fig. 15) securely.
adjusting hardware at the top of the leg set (Fig. 5)
adjust the rail table, along its length, gauging against
the front rail (Fig. 13). Once level, front and back,
tighten the adjusting hardware, the M8 cap head
screws in the top of the legs, and the M8 x 20 carriage
bolts through the front rail brackets securely.
NOTE: If you are installing the extension table with a
Mobile Base, the M8 cap head screws in the top of the
legs, shown in Figure 6, may extend below the slot in
the table. These two screws are used for assembly and
are not necessary once the cross members are in
place.
STEP 23. Attach 52" rear rail (Fig. 17).
You will need: 5 - 10 x 35mm hex head screws
5 - 10mm flat washers
5 - 10mm lock washers
5 - 10mm nuts
Attach through the slotted holes in the rear support
brackets and the side of the 52" rail table using the M10
bolts. Secure each bolt with a flat washer, lock
washer, and nut, keeping the washers and nuts to the
inside. Tighten snug the hardware that attaches to the
saw table, leaving the remaining finger tight. (If you are
also adding a Slide Table accessory, assemble it before
attaching the rear rail. If adding an Outfeed Table
accessory, check that you have Outfeed Table hanger
brackets attached to the saw table instead of the rear
Using the
support brackets and continue.)
FIG. 16
STEP 24. Parallel the rear rail to the saw table top (Fig.
STEP 25. Install motor cover (Fig. 18). Remove the two
STEP 26. See DW746 manual for Table Saw operating
5
13). Using your fence face or a straightedge to extend
the table surface over the rail, make sure the distance
from the saw table top to the rail top is the same at both
the left and right side of the saw table. If the rail is not
aligned correctly, loosen the mounting screws slightly
and tap on the rail with a soft hammer or a regular
hammer and a block of wood until the distances are the
same. Tighten the hardware securely. Repeat for the
three remaining attachment points checking the
distance along the full length of the rail.
screws and washers from the top of the two side legs
with a small flat blade screwdriver (or T25 Torx driver).
Snap the two bottom tabs of the cover into the slots in
the right crossmember. Lower support rails are very
close to the crossmember slots, it may be necessary to
slightly loosen carriage bolts holding the rails to
engage tabs. Place the cover in position and re-install
the screws and washers.
instruction and adjustments.
FIG. 18
FIG. 16
FIG. 19