Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame rail
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75758F
Wrenches: 11/16"
Wrenches: 11/16"
Lift gate sensor reduced to this
area on vehicles with the "Hand
free lift gate" option.
Figure 2
File
INSTRUCTIONS:
1 . Check to see if spacer and bolt head will fit through access hole, if not
modify hole to accept hardware, the illustration above shows two ways of
achieving this, the first is using a file, the second is by inserting a wrench or
prying as shown. Enlarge hole just enough to get hardware through.
Qty. (4)
Carriage bolt 7/16-14 X 1.50 GR5
Qty. (4)
Spacer ¼ X 7/8 X 3.00
Qty. (4)
Conical washer 7/16
Note: With the hitch installed on vehicle with "Hands free lift gate" options it will only work in limited area.
See Figure 2.
1.
Feed spacers and carriage bolts into position using the pull wires provided (both rail). Leave pull wire attached. Note: It is much
easier if bolt and spacer are not engaged while inserting them into frame, refer to illustration. See Figure 3.
i
if b lt
d
2.
Push (only) fasteners back into frame rail leaving pull wire and the extra wire sticking out of the frame rail.
3.
Raise hitch into position between frame rails, feed pull wires thru adjacent holes in the hitch. On the passenger side raise the
forward end of the bracket over the hoses crossing the frame rail (not shown).
4.
Pull fastener back through access holes and hitch.
5.
Remove pull wires and attach conical washers and nut (be careful not to push fastener back into frame rail).
6.
Tighten to specification.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
©
2014 Cequent Performance Products, Inc –
Installation Instructions
Fascia
Tail pipe
Frame rail
Access hole
Wrench
t
d hil i
ti
Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all 7/16 14 GR5 fasteners with torque wrench to 50 Lb Ft (68 N*M)
Printed in México
Ford Escape
Do Not Exceed Lower of Towing Vehicle
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV 1 & 2
Figure 1
Vehicle forward
Note: Fasteners typical both sides
Qty. (4)
Hex nut 7/16-14 GR2
Qty. (4)
Pull wire 7/16
th
i t f
f
t ill
Sheet 1 of 3
75758N
Part Numbers:
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
5000 (2270 Kg)
3500 (1589 Kg)
Accessory Rating
Kink pull wire to keep
spacer independent of bolt
Figure 3
Access hole
t ti
S
Fi
3
8-1-2014
Form: F205 Rev A 5-6-05
75758
87627
44681
Max Tongue
WT (LB)
525 (239 Kg)
525 (239 Kg)
C
Rev. C
Publicidad
Manuales relacionados para Cequent Performance Products 75758
Resumen de contenidos para Cequent Performance Products 75758
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2014 Cequent Performance Products, Inc – Printed in México Sheet 1 of 3...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. © Feuille 2 de 3 75758N 8-1-2014 Rev. C 2014 Cequent Performance Products, Inc – Imprimé au Mexique Form: F205 Rev A 5-6-05...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2014 Cequent Performance Products, Inc. – Impreso en México Hoja 3 de 3...