Cequent Performance Products 24886 Instrucciones De Instalación

Fascia
Hitch Shown In Proper Position
Equipment Required: Metal File
Fastener Kit: 24886F
Wrenches: 3/4"
Drill Bits: 1/2", 3/8"
Enlarge to 1/2" - typical
Both sides
Remove plastic plugs
From existing holes
Both sides
43 43
43 43
Existing 7/8"
Diameter hole
in frame
3/8" dia. Drilled holes
Figure 2
Access hole modification to allow
fishwiring of block and carriage bolt
1 1 1 1 Qty. (4) Carriage Bolt – ½-13 x 1.75 GR5
2 2 2 2 Qty. (4) Spacer – ¼ x 1 x 3 (Square hole)
3 3 3 3 Qty. (4) Conical Washer – ½"
1. Lower exhaust by disconnecting rubber exhaust hangers from hanger brackets, 2 each side.
2. Remove plastic plugs from existing holes in frame rails and discard.
3. Use 3/8" drill and file to modify forwardmost hole in each frame rail, as shown in Figure 2, to allow fishwiring of spacers and carriage bolts.
4. Use ½" drill bit to enlarge rearmost hole in frame rail, both sides
5. Fishwire spacer and carriage bolt thru access hole modified in step 3 and down thru rearmost hole in each frame rail (see figure 3). Insert
remaining blocks and carriage bolts into access holes and drop back down thru holes, making sure blocks span both sides of hole (see figure
4).
6. Raise hitch into position, with ¼ x1/1/2 x 2 spacer between frame and hitch bracket at forward attachment as shown, being careful not to push
fasteners into frame, and secure with conical washers and nuts. Tighten ½-13 GR5 fasteners to 75 lb.-ft. (102 N*M)
7. Raise exhaust back into position and reattach exhaust hangers disconnected in step 1.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z 2012, 2015 Cequent Performance Products, Inc. - Printed in Mexico
Installation Instructions
Subaru Impreza 5-Dr. Wagon
Including older Outback Sport & WRX
(Will not fit vehicles with quad exhaust outlets)
Subaru XV Crosstrek
(Sold separately)
Drawbar Kit:
3593
Drawbar must be used in the
RISE position only.
1 1 1 1
2 2 2 2
1 1 1 1
2 2 2 2
5 5 5 5
Spacer between frame and
Hitch bracket - typical
43 43 43 43
4 4 4 4
5 5 5 5
6 6 6 6
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, PC4
A. Insert bolt and
Block into frame
34 34 34 34
1 1 1 1
2 2 2 2
1 1 1 1
2 2 2 2
Qty. (4) Hex Nut – ½-13
Qty. (2) Spacer – ¼ x 1-1/2 x 2
Qty. (2) Pull wire – ½"
24886N
Part Numbers:
24886
60303
77274
24810
B. Align block on
C. Pull bolt thru
access hole
block
Figure 4
Fishwiring Procedure
Modify this hole - both
sides to allow fishwiring-
See figure 2
5 5 5 5
34 34 34 34
Figure 3
Kink pull wire to keep
Spacer independent of bolt
10-6-2015 Rev. C
Form F206 Rev B 9-17-2012
UHaul