Cleaning & Maintenance - Chicco Walky Talky Manual De Instrucciones

• Do not use this product with tem-
d-
perature below 5 °C or on slippery
m-
and/or icy surfaces.
• Do not use this product as a sledge
er
or raft in the water.
ri-
• Check the baby walker regularly for
signs of wear and damage.
n-
• Always check that the stoppers are
ho
fitted correctly and show no sign of
m
damage or tear.
il-
• Do not allow other children to climb
onto or play without the supervision
nt
of an adult near the baby walker.
by
• When not in use, store the baby
walker in a suitable place, away
at
from contact with all weather con-
d
ditions and out of the reach of chil-
dren.
ay
u
CLEANING & MAINTENANCE
The cleaning and maintenance operations must only be
or
carried out by an adult.
Clean the fabric and plastic parts including the stopper
with a damp cloth.
n,
Do not use solvents or abrasive products for cleaning.
h
Dry the metal parts to prevent the formation of rust.
PADDED SEAT COMPOSITION:
ve
100% polyester outer layer, 100% polyurethane inner layer
ut
Wash by hand in cold water
d
Do not bleach
d;
d
ri-
Do not tumble dry
d.
ys
Do not iron
he
Do not dry clean
d
COMPONENTS/PARTS
ht.
A) Structure of the baby walker
B) Upholstered padded seat
to
C) Rigid spoiler
al-
D) 2 front swivel wheels
ur
E) 2 rear fixed wheels
F) 6 stoppers
G) Electronic toy panel
ht
H) Padded seat fixing bands
I) Bar support
a-
FIRST ASSEMBLY OF THE BABY WALKER
1. Turn over the structure (A) of the baby walker. Attach the
front wheels (D) in their slots as shown in figure 1. Make
sure the wheel pin has come to its limit.
2. Attach the rear wheels (E) in their slots as shown in figure
2. Make sure the pin has come to its limit: a click will be
heard and the fastening pin will appear from the hole.
3. Secure all the stoppers (F) in their slots as shown in figure
3. Make sure that the pins of all the stoppers have come to
their limit.
4. Bring the baby walker to position for use by turning the
wheels to the floor (levelled and horizontal); slowly lift the
upper part of the structure as shown in figure 4, by pulling
it upwards until it clicks into place in the desired position.
WARNING: Before putting the child in the baby walker,
make sure the knob located below the upper part of the
structure has reached its engagement position: a click will
be heard to indicate it is locked (fig. 4a). Then push down
the structure to ensure the proper engagement.
5. Insert the front tabs of the rigid spoiler (C) into the slots
cut on the upper part of the structure (A) and push down
on the back until a click is heard locking them (fig. 5).
WARNING: Once the spoiler is inserted it's no longer possi-
ble to pull it out. Do not try to remove it with a screwdriver
or other tool.
6. Insert the padded seat plastic rings (B) in the slots
formed along the top edge of the baby walker (fig. 6) and
make sure they are properly locked in the shown position
(fig. 7-8).
7. The electronic toy panel with sounds and lights can be
placed on the upper part of the structure with a simple
pressure (fig. 9); It does not require any type of fixing. Bat-
teries not included; the toy has two holes located under it
to allow to fix the toy on different parts of the baby walker,
through the included fixing bands (fig. 10).
WARNING: To prevent the risk of suffocation, the electron-
ic toy panel must be fixed to other parts using only items
included (fixing bands), do not add laces.
WARNING: When the toy is not fixed to other parts keep
the bands out of reach of children; do not place the toy on
the baby walker with the fixing bands mounted.
WARNING: The bar support must be installed by the par-
ent before allowing the baby to use the walker.
8. The bar support (I) with movable toys is installed by in-
serting side intersections in their seats on the top of the
structure, pushing down until they click (fig. 11-12).
HEIGHT REGULATION OF THE BABY WALKER
WARNING: When opening, closing or regulating the baby
walker, make sure that your child is at a safe distance.
9. To open the baby walker slowly lift the upper part of the
structure by pulling it upwards and supporting it from be-
low until it clicks into the desired position (fig. 4).
10. To adjust the seat height, after taking the child from the
baby walker, push the upper part of the structure upwards
until it clicks into its locked position. To lower the height
move the knob located below the upper part of the struc-
ture and turn it counter-clockwise (fig. 13), push the knob
up, accompany the upper part to the desired position (fig.
14). Upon release of the pin, the structure is automatically
locked. The height can be adjusted to three different po-
sitions.
WARNING: Before putting the child in the baby walk-
11