Chapin Sk-1154-1 Manual De Instrucciones

WARNING
WARNING: Improper use or failure to follow instructions can result in explosive failure causing
serious eye or other injury. For safe use of this product you must read and follow all instructions. Do not
leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion.
Do not store or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants
and full foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump to prevent ejecting pump
assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than
the original pump. Do not attempt to modify this sprayer. Replace parts only with manufacturer's original
parts. Never spray flammable, caustic, acidic, chlorine, bleach or other corrosive solutions or heat,
pressure, or gas producing chemicals. Always read and follow chemical manufacturer's instructions
before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
WARNING: This product contains chemicals, including lead, known to the state of
California to cause birth defects and other reproductive harm. Wash hands after handling.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
Felicitaciones!
¡
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas? No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ? Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
Parts, Piezas, Pièces
6-6136 6-5943 6-4626
Hose Nozzle Shut-off Handle
Manguera Tobera Mango de cierre
Tuyau Buse Poignée du robinet
6-7756 Extension wand, Vara de extensión, Rallonge 6-7749 Extension wand, Vara de extensión, Rallonge
(31010, 31020, 31030, 36140) (30220)
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d'étanchéité (non inclus) 6-1925
1. Hose to Tank
1A
Hose Barb
2. Nozzle
2A
Sk-1154-1
Attach nozzle to shut-off handle or extension wand.
3. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace
hose before using. Replace with original manufacturer's parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for
signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could
result in explosive bursting under pressure. If any of these signs are found, discard tank immediately and replace.
Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 strokes and
inspect for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with Filling,
Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting. If any of these
conditions are found, replace affected part with original manufacturer's part before using.
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
5. Pressurizing and Spraying
6-3337
Strap, Correa, Sangle
( 31020, 31030, 36140, 30220)
5A
Turn handle clockwise to
tighten. Push handle down,
turn 1/4 turn counterclock-
wise to release.
011269-3 (A) R0116
Make sure hose is pushed all the way to the tank.
Make sure hose clamp is tight and below the hose
barb. Turn clockwise with a screwdriver to tighten.
2B
5B 5C
5D
Pump until you feel Push handle, down, turn Adjust spray pattern by
resistance. 1/4 turn clockwise to turning nozzle cap. Do not
lock. Begin spraying. turn cap more than 2 turns
Re-pump sprayer as or cap may come off allow-
required to maintain ing spray material to spray
spray force. back on you.
6. To Release Pressure
1) Do: With pump facing away, turn locked handle counterclockwise until air begins to escape. Stop
turning handle when you hear air escaping.
2) Do: Stay away from the sprayer until all air has escaped.
7. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing and
Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are thor
oughly rinsed with water after each use.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening incover.
8. Fatigue-Free Spraying
For constant spraying, push down on shut-off handle and move grey
locking mechanism away from you. To release, squeeze handle and move
the grey locking mechanism back towards you. ( Not all models are
provided with this feature).
9. Troubleshooting
Tank pressurizes but does not spray.
-
WARNING:
Release pressure in tank before troubleshooting.
Clean shut-off (Fig. 9A- 9D)
9A 9B
Handle
Pull handle straight Insert notches from
up. underside of handle into
plunger grooves and turn
counterclockwise.
Tighten plunger clockwise until flush to
9D
top of shut-off body. Do not over-tighten
Plunger flush
with body
or unit may not spray. Slide forks under
plunger, push handle down until it snaps
into place.
Clean Nozzle Assembly (Fig. 9E) Remove nozzle cap by unscrewing. Clean and re-assemble.
-
9E
Nozzle Cap
8A
Locking
mechanism
9C
Plunger
Diaphragm
Spring
Remove plunger, diaphragm and spring.
Wash diaphragm with mild detergent. Reas-
semble: Hold shut-off upright as shown,
place spring in hole, place diaphragm on
top of spring. Reassemble plunger and
tighten.