Chapin Sk-1154-1 Guia De Inicio Rapido

WARNING
WARNING: Improper use or failure to follow instructions can result in explosive failure
causing serious eye or other injury. For safe use of this product you must read and follow all
instructions. Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-
up resulting in possible explosion. Do not store or leave solution in tank after use. Always wear
goggles, gloves, long sleeve shirt, long pants and full foot protection when spraying. Never use
any tool to remove pump if there is pressure in sprayer. Never stand with face or body over top of
tank when pumping or loosening pump to prevent ejecting pump assembly and/or solution from
striking and injuring you. Never pressurize sprayer by any means other than the original pump. Do
not attempt to modify this sprayer. Replace parts only with manufacturer's original parts. Never
spray flammable, caustic, acidic, chlorine, bleach or other corrosive solutions or heat, pressure,
or gas producing chemicals. Always read and follow chemical manufacturer's instructions
before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
Parts, Piezas, Pièces
6-2001
Hose Kit: 2 nuts, 2 barbs and hose
Juego de manguera: 2 tuercas ,2 lengüetas y manguera.
Nécessaire de tuyau: Deux écrous, deux ardillons et tuyau
6-2000 6-6003 6-8260
Shut-off Handle Nozzle Foaming Nozzle
Mango de cierre Boquilla
Boquilla
Poignée du robinet Buse Buse
6-7749
Extension wand (poly)
Vara de extensión
Rallonge
6-1925
Repair Kit (not included)
Juego de reparación (no incluido)
Kit de réparation (non inclus)
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
To prevent hose from blowing off, hose must cover both barbs on the outlet tube adapter and
touch flange (Fig. 1B) before hose nut is securely tightened (Fig. 1C).
1. Hose to Tank
1A
Filter
Dis-
Outlet
charge
Tube
Assembly
Tool
Holder
Discharge/ Tool Holder Assembly
• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1A).
• Firmly insert the outlet tube portion into the tank adapter (Fig. 1B) leaving no gap between the tank adapter
and outlet tube adapter. Firmly tighten the retaining nut to the tank adapter (Fig. 1C).
2. Nozzle / Extension Wand
2A
Sk-1154-1
Attach nozzle to extension wand (Fig. 2A).
FOAMING NOZZLE INSTRUCTIONS
Figure A
To spray from straight stream to fine mist, flip up screened foamer
cover. Adjust nozzle by turning to provide desired spray pattern.
Figure B
To spray as a foam, secure screened foamer cover to closed position.
Adjust nozzle for desired foam patterns.
3. Filter
The filter helps prevent clogging while spraying. It is located on the end of the outlet
tube inside your sprayer tank.To clean filter, remove the discharge assembly from
the tank (Fig.1A). Make sure the filter is positioned at the bottom of the tank as
pictured (Fig. 3A).
4. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found,
replace hose before using. Replace with original manufacturer's parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank
for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening
and could result in explosive bursting under pressure. If any of these signs are found, discard tank
immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20
strokes and inspect for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and
proceed with Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting. If any of
these conditions are found, replace affected part with original manufacturer's part before using.
5. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and
tighten securely.
016354R0522
WARNING
1C
1B
No Gap
Retaining Nut -
Securely tightened.
Outlet
Tube
Adapt-
Tank
er
Adapter
Figure A
Figure B
3A
Filter
6. Pressurizing and Spraying
6B
6A 6C
Do: Turn handle Do: Pump until you Do: Push handle,
clockwise to tighten. feel resistance. down, turn 1/4 turn
Push handle down, clockwise to lock.
turn 1/4 turn Begin spraying.
counterclockwise to Re-pump sprayer as
release. required to maintain
spray force.
7. To Release Pressure
Do: With pump facing away, turn locked handle counterclockwise until air begins to escape.
Stop turning handle when you hear air escaping.
Do: Point pump away until all air has escaped.
8. Care, Storage and Maintenance
1) Do: Follow chemical manufacture's instructions for cleaning. Rinse thoroughly with recommended
solvent. Follow Filling, Pressurizing and Spraying Instructions, except pump unit only 8-10 strokes. Be sure
that the wand and nozzle are thoroughly rinsed after each use.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
9. Troubleshooting
-
Tank pressurizes but does not spray.
WARNING:
Release pressure in tank before troubleshooting.
Clean shut-off (Fig.9A- 9D)
9A 9B
Handle 9C
Plunger
Diaphragm
Spring
Remove plunger,
Pull handle Insert notches
diaphragm and spring.
straight up. from underside of
Wash diaphragm with mild
handle into plunger
detergent. Reassemble:
grooves and turn
Hold shut-off upright as
counterclockwise.
shown, place spring in
hole, place diaphragm on
top of spring. Reassemble
plunger and tighten.
9E
Nozzle Cap
Clean Nozzle Assembly (Fig. 9E)
Remove nozzle cap. Clean and re-assemble.
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.1-800-950-4458 www.chapinmfg.com
6D
Do: Turn end of
nozzle to adjust
spray pattern.
9D
Plunger flush
with body
Tighten plunger clockwise until
flush to top of shut-off body.
Do not over-tighten or unit may
not spray. Slide forks under
plunger, push handle down
until it snaps into place.