Descargar Imprimir esta página

Publicidad

Enlaces rápidos

WARNING
WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious
eye or other injury. For safe use of this product you must read and follow all instructions. Do not leave a
pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion.
Do not store or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants
and full foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump to prevent ejecting pump
assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than
the original pump. Do not attempt to modify this sprayer. Replace parts only with manufacturer's original
parts. Never spray flammable, caustic, acidic, chlorine, bleach or other corrosive solutions or heat,
pressure, or gas producing chemicals. Always read and follow chemical manufacturer's instructions
before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
Parts, Piezas, Pièces
6-5797
6-1866
6-6141
Nozzle .5GPM
Shut-off Handle
Hose
Tobera
Mango de cierre
Manguera
Buse
Poignée du robinet
Tuyau
6-5373
6-3337
Holster
Strap
Funda
Correa
Étui
Sangle
6-7703
Extension wand, Vara de extensión, Rallonge
6-4629
Repair Parts Kit Gaskets and Seals (not included)
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d'étanchéité (non inclus)
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
1. Hose to Tank
1A
Make sure hose is pushed all the way
Hose Barb
to the tank. Make sure hose clamp
is tight and below the hose barb.
Turn clockwise with a screwdriver to
tighten.
2. Nozzle
2A
Attach nozzle to shut-off handle or extension wand.
3. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
Sk-1154-1
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these
conditions are found, replace hose before using. Replace with original manufacturer's
parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect
interior and exterior of tank for signs of deterioration of body and bottom. Any sign of
deterioration indicates possible tank weakening and could result in explosive bursting
under pressure. If any of these signs are found, discard tank immediately and replace.
Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only
(Pump plunger 10-20 strokes and inspect for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions),
empty tank, and proceed with Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion
and pitting. If any of these conditions are found, replace affected part with original
manufacturer's part before using.
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to
accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump
in tank and tighten securely.
5. Pressurizing and Spraying
5a
Turn handle clockwise to
tighten.Push handle down,
turn 1/4 turn counterclock-
wise to release.
018336R0222
2B
5b
5c
Pump until you
Push handle, down, turn 1/4 turn
feel resistance.
clockwise to lock. Begin spraying.
Re-pump sprayer as required to
maintain spray force.
6. To Release Pressure
1) Do: With pump facing away, turn locked handle counterclockwise until air begins to
escape. Stop turning handle when you hear air escaping.
2) Do: Stay away from the sprayer until all air has escaped.
7. Care, Storage and Maintenance
1) Do: Follow chemical manufacture's instructions for cleaning. Rinse thoroughly with
recommended solvent. Follow Filling, Pressurizing and Spraying Instructions,
except pump unit only 8-10 strokes. Be sure that the wand and nozzle are thoroughly
rinsed after each use.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and
empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through
opening in cover.
8. Install Holster
A. Squeeze shut-off
B. Place shut-off handle
handle.
through holster opening.
C. Push through
D. Feed holster down
opening in holster.
hose.
E. Push holster over outlet.
F. Slide holster in clip.
G. Lock bottom of
holster in clip on
side tank.
H. Assembled
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com

Publicidad

loading

Resumen de contenidos para Chapin Sk-1154-1

  • Página 1 Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba. Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut. H. Assembled Congratulations! You have just purchased a quality Chapin product. Turn handle clockwise to Pump until you Push handle, down, turn 1/4 turn Register Your Sprayer Online @ www.chapinmfg.com Questions? Do Not Return To Store.
  • Página 2 • Gire el mango hacia la derecha para ajustarlo (Fig.5A). Vous avez acheté un produit de qualité Chapin. Enregistrez dès que possible votre pulvérisateur en ligne à 2) Oui : Inspectez le boyau pour tout signe de détérioration, fissures, mollesse ou fragilité. Si vous découvrez •...