Chapin Sk-1159-1 Manual De Instrucciones

WARNING
WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious
eye or other injury. For safe use of this product you must read and follow all instructions. Do not leave a
pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion. Do not
store or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot
protection when spraying. Never use any tool to remove pump if there is pressure in sprayer. Never stand with
face or body over top of tank when pumping or loosening pump to prevent ejecting pump assembly and/or
solution from striking and injuring you. Never pressurize sprayer by any means other than the original pump.
Do not attempt to modify this sprayer. Replace parts only with manufacturer's original parts. This sprayer is
designed for acidic solutions only. Never spray flammable, chlorine or bleach, caustic, or other corrosive
solutions or heat, pressure, or gas producing chemicals. Always read and follow chemical manufacturer's
instructions before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
Parts, Piezas, Pièces
6-8093
6-8148
Poly Adjustable
Nozzle Kit
Nozzle
Tobera
Tobera
Buse
Buse
6-8096
6-8241
Flat Fan
Shut-off Assembly
Nozzle
Unidad de cierre
Tobera
Assemblage d'arrêt
Buse
6-8242
Extension wand, Vara de extensión, Lance de rallonge
Elbow O-ring Hose Washer 6-8243
O-ring Kit
Kit de junta tórica
Trousse de joint torique
Nozzle Gasket Wand O-ring
Filter
6-8244
Repair Parts Kit Gaskets and Seals (not included),
6-5388
Juego de piezas de reparación, empaquetaduras y
Hose Assembly
juntas (no incluido)
Ensamblaje de la manguera
Kit de pièces de réparation, joints et garniture
Assemblage de boyau
d'étanchéité (non inclus)
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
1. Assembly of Shut-off, Extension Wand and Nozzle
1A
Retaining Nut
Shut-off Assembly
1) Screw nozzle assembly onto threaded end of the extension wand securely.
2) Insert unthreaded end of extension into shut-off assembly as shown and tighten retaining nut securely.
Nozzle Assembly
Figure 1
Unscrew the nozzle cap (1) from the nozzle body (3) with retaining nut (2) fastened tightly to the elbow (5).
Unscrew the retaining nut (2). Push the nozzle body (3) with the nozzle gasket (4) out of the retaining nut (2). To
reinstall the nozzle, reverse the above instructions.
Figure 2
Unscrew the retaining nut from the elbow and push the fan nozzle tip and gasket out of the retaining nut.
To reinstall the nozzle, reverse the above instructions.
1. Poly
Nozzle Cap
Sk-1159-1
2. Retaining
Nut
3. Nozzle
4. Nozzle
Gasket
2. Filter
The filter helps prevent clogging while spraying. It is
located on the end of the white tube inside your sprayer
tank.To clean filter, remove the hose from the tank and
lift out the outlet tube. Make sure the filter is positioned at
the bottom of the tank as pictured.
3. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are
found, replace hose before using. Replace with original manufacturer's parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and
exterior of tank for signs of deterioration of body and bottom. Any sign of deterioration indicates
possible tank weakening and could result in explosive bursting under pressure. If any of these
signs are found, discard tank immediately and replace. Do not attempt to patch leaks, etc., as this
could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only
(Pump plunger 10-20 strokes and inspect for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank,
and proceed with Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting.
If any of these conditions are found, replace affected part with original manufacturer's part
before using.
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: over fill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and
tighten securely.
014917R0222
Nozzle Assembly
Extension Wand
Retaining
Nut
Fan Nozzle
Tip
Body
Nozzle
Gasket
Elbow
5. Elbow
Figure 1 Figure 2
2a
Filter
5. Pressurizing and Spraying
5A 5A
5A 5A 5B 5B
Do: Turn handle Do: Pump until you Do: Push handle, down, turn 1/4
clockwise to tighten. feel resistance. turn clockwise to lock. Begin
Push handle down, spraying. Re-pump sprayer as
turn 1/4 turn counter- required to maintain spray force.
clockwise to release.
6. To Release Pressure
6A 6A
1) Your sprayer is equipped with a pressure
relief/release valve (Fig. 6A). To release
pressure lift and hold the cap until air is
completely exhausted, or, turn the valve slowly
counter-clockwise until you hear air escaping
and wait air is completely exhausted (Fig. 6B).
2) Do: Stay away from the sprayer until all air
has escaped.
7. Care, Storage and Maintenance
1) Do: Follow chemical manufacture's instructions for cleaning. Rinse thoroughly with
recommended solvent. Follow Filling, Pressurizing and Spraying Instructions, except pump unit
only 8-10 strokes. Be sure that the wand and nozzle are thoroughly rinsed after each use.
2) Do: Open shut-off and allow recommended solvent to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening
in cover.
8. Fatigue-free spraying
LOCK-OFF POSITION LOCK-ON POSITION
8a Locking Mechanism
8b 8c
Handle
Down
Handle
Up
For safety lock-off feature (no-spraying), pull up on handle and move red locking mechanism into
lock-off position as shown in fig. 8a. To disengage, push down on handle and return red locking
mechanismto neutral position as in fig. 8c. For lock-on feature (continuous spraying), push down
on handle and move red locking mechanism into lock-on position as shown in fig. 8b. To disengage,
push down on handle and return red locking mechanism to neutral position as shown in fig. 8c.
9. Replacing Hose to Tank
9A 9B 9C
Black
No gap
Adapter
Make sure black Press hose over Make sure worm
adapter is attached to adapter. gear clamp is below
outlet tube adapter. black adapter .
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com
5C 5C
6B 6B
NEUTRAL POSITION
9D
Tighten clamp fully.