Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
ATTACHING EXTENSION CORD TO MOWER (FIGURE 5)
DO NOT connect the extension cord to power source until you have finished
reading this manual and you are ready to start mowing.
1. The extension cord must be polarized and will only plug in one way, orient the
wide slot with the wide blade in the switch housing.
2. Loop the extension cord and push the loop up through the hole in the switch
housing.
3. Pull the extension cord on the side of the loop that is plugged into the switch
housing and remove all the slack in this section of the extension cord.
4. Place the loop over the strain relief tab on the switch housing and pull the
extension cord so the loop draws down around the strain relief tab as shown
in the detail. Double check to see that you did not loosen the extension cord.
5
SWITCH USE (FIGURE 6)
Your mower is equipped with a special switch. To operate the switch, insert your
finger into the opening (Figure 6) and push the lever out so that you can grasp it
with your other hand. Pull the lever back to turn the unit on and hold it against the
mower handle to keep it running. To turn the mower off, just release the lever. The
spring loaded "SNAP ACTION" lever will quickly turn the mower off.
CAUTION: NEVER ATTEMPT TO OVERRIDE THE OPERATION OF THIS SWITCH.
6
EXTENSION CORD TO ELECTRICAL OUTLET (FIGURE 7)
1. Place most of the extension cord close to the electrical outlet, out of the path of
the mower. Attach extension cord to mower.
2. Start in direction where extension cord side of mower is closest to the outlet.
Begin mowing in the area closest to the outlet and mow in a back and forth
manner. When you come to the end of a row being cut, release the power
switch and wait for the blade to come to a complete stop. Pull the handle
release lever and flip the handle to the opposite side of the mower. Release
the handle lever and ensure the handle is secure. Pull power switch to re-start.
Note the cord is kept on cut portion of lawn and out of the path of the mower.
(Figure 7)
3. Avoid mowing in circles as cord will be harder to manage.
7
FLIP-OVER HANDLE FEATURE (FIGURE 8)
1. By pulling the handle release lever and flipping the handle to the opposite side
of the mower, the cord remains on the same side of the mower and out of the
way.
2. You must mow in a back and forth pattern to benefit from this feature.
8
RECOMMENDED APPROXIMATE CUTTING HEIGHT
The cutting height should be higher in hot weather or shade , and
lower for the last mow before winter.
COOL SEASON GRASSES
TYPE
CREEPING BENT GRASS
VELVER BENT GRASS
ANNUAL BLUEGRASS
CANADA BLUEGRASS
KENTUCKY BLUEGRASS
ROUGH BLUEGRASS
SMOOTH BROMEGRASS
FINE RESUE
TALL FESCUE
ANNUAL RYEGRASS
WARM SEASON GRASSES
TYPE
BAHIA GRASS
BERMUDA GRASS
BUFFALO GRASS
CARPET GRASS
CENTIPEDE GRASS
ST. AUGUSTINE GRASS
ZOYSIA GRASS
NOTE: The cut height range for your mower is 1" - 3-1/2"
WHEEL HEIGHT ADJUSTMENT (FIGURE 9)
1. BEFORE MAKING ANY ADJUSTMENTS, TURN OFF, UNPLUG MOWER AND
WAIT FOR BLADE TO STOP.
2. Your mower features the Black & Decker single lever wheel height adjust system.
This system will adjust all four wheels at the same time. Mower adjusts from 1 to
3 1/2" with six increments.
3. Place your left hand on the height adjust handle and your right hand on the
lower handle as shown in Figure 9.
4. Pull height adjust handle away from mower, and re-set in the desired height
adjust position. (See recommended cut height by grass type under
OPERATING INSTRUCTIONS) Rotating the height adjust towards the front of the
mower lowers the cut height, and rotating towards the rear raises the cut height.
9
LOW
SHADE
SUN
1-1/3"
2/3"
1/4"
1/2"
1/2"
1"
3"
4"
2-1/2"
3"
1"
1-1/2"
3"
4"
1-1/2"
2-1/2"
2-1/2"
4"
2"
2-1/2"
SHADE
SUN
2"
3"
1/2"
1"
1-1/2"
2-1/2"
1"
2"
1"
2"
2"
3"
1/2"
1"
CUTTING HEIGHT POSITIONS
Position
1 (LOW)
2
3
4
5
6 (HIGH)
HIGH
Cut
1"
1-1/2"
2"
2-1/2"
3"
3-1/2"
Publicidad
Tabla de contenido
