Bosch EasySander 12 Manual Original página 13

(1) Battery charge indicator/overload indicator
(2) On/off switch
A)
(3) Battery
(4) Battery release button
A)
(5) Sanding sheet
(6) Sanding plate
(7) Handle (insulated gripping surface)
(8) Extraction outlet
(9) Dust protection cover
(10) Dust extraction adapter
A)
(11) Universal adapter
A)
(12) Extraction hose
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Cordless multi-sander
Article number
Rated voltage
No-load speed
No-load orbital stroke rate
Sanding sheet surface
Orbit diameter
Weight according to
EPTA-Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
A)
ure during operation and
during storage
Recommended batteries
Recommended chargers
A) Limited performance at temperatures <0 °C
Noise/Vibration Information
Noise emission values determined according to
EN 62841-2-4.
Typically, the A-weighted sound pressure level of the power
tool is less than 70 dB(A). The noise level when working can
exceed the volume stated. Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-4:
2 2
a = 5.5 m/s , K = 1.5 m/s ,
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
Bosch Power Tools
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
A)
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
u
EasySander 12
3 603 J76 9..
V= 12
−1
min 11,000
Charge the battery
−1
min 22,000
u
2
cm 104
mm 1.2
Note: The battery is supplied partially charged. To ensure
kg 0.70
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
°C 0 to +35
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
°C –20 to +50
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
PBA 12V...
is discharged, the power tool is switched off by means of a
AL 11..CV
protective circuit: The application tool no longer rotates.
GAL 12...
u
Note: If the power tool shuts down automatically because
the battery is flat or overheated, switch the power tool off
using the on/off switch (2). Charge the battery or let it cool
down before switching the power tool on again. Failure to do
so can damage the battery.
To remove the battery (3), press the release button (4) and
pull the battery back and out of the power tool. Do not use
force to do this.
Follow the instructions on correct disposal.
Dust/chip extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
1 609 92A 5GX | (27.11.2019)
English | 13