Worx WG430E Traducción De Las Instrucciones Originales página 9

OpERATIOn InSTRUCTIOnS
NOTE: Before using the tool, read the
instruction book carefully.
ASSEmBLE THE mACHInE
cauTION: Take care when taking
the components out of the color
box. Don't separate the parts by force
and confirm each part is intact. If any
part is broken, please contact the
service agent.
1. uNPack ThE machINE
1) Take the three legs (6) out of the funnel.
(See fig. A)
2) Take the funnel cover off by pressing the
locking button as shown in fig.B.
3) Remove the motor housing from the
funnel. (See fig.C)
4) Take the funnel out of the stand. (See fig.D)
2. aSSEmBLE ThE muLchEr STaND
Insert the three legs into the stand as shown
in fig. E1. Make sure the alignment/release
button of each leg (a) is properly positioned
and extended into each hole of the upper
portion of the stand. (See Fig.E2)
3. aSSEmBLINg ThE muLchINg POwEr
hEaD
1). Placing the motor housing on the stand.
Make sure the motor housing is stable on
the stand. (See fig.F)
2). Fit the funnel onto the motor housing.
Make sure it's locked down by the clamps
found on the motor housing. (See fig.G)
3). Fit the funnel cover over the funnel. Make
sure the locking tabs of the funnel cover
are securely attach to the funnel. (See fig.H)
cauTION: Properly attach the funnel cover
to the funnel by aligning the notches (b) of
each piece.
4. FITTINg a cOLLEcTION Bag
If you use a plastic collection bag, roll it over
the top of the stand like you would with trash
bag being used on a trash can. (See Fig.I1)
Leaf mulcher
5. rEmOVINg a FuLL cOLLEcTION Bag
1) When the bag is full, turn off the mulcher
then unplug it. Lift the mulching power
head from the stand. (see fig.I2)
2) Lift the stand off of the collection bag from
the top. (See fig.I3)
OPEraTION
1. ON/OFF SwITch
The ON/OFF switch is located on the lower
side of the motor housing portion of the
power head. To turn on, pull out the switch.
(See Fig.J1)
To turn off, push the switch in. (See Fig.J2)
cauTION: To prevent exposure to
dusty warm air don't stand in front
of the motor ventilation slots.
2. LOaDINg YOur machINE
With the mulcher running, feed double
handfuls of dry leaves, or single handfuls of
wet leaves, into the funnel. Allow the machine
to shred the load completely and regain speed
before inserting the next handful. Do not
overload the machine by letting it labor at low
speed: this may cause the motor to stop. If
this happens, turn the switch off, unplug the
machine, clear the unshredded material from
the funnel, restart the machine, and continue
with your shredding.
warNINg: Filling mulcher with
unshredded material at a rate faster
than the machine can handle may result
in permanent damage to your motor.
always wear protective glasses and a
mask.
mAInTEnAnCE
1. cLEaNINg YOur uNIT
Your unit requires a minimum of maintenance
other than cleaning. It is recommended that
you clean out built –up residue inside the
housing area during and after each use. When
fully disassembled, clean the funnel cover
and funnel with clean water, while using a
dry cloth to clean the motor housing. Replace
cutting line as often as necessary and clean
air filter frequently. Any other maintenance or
repairs should be performed.
9 9
En