Residual Risks; Know Your Product - Ryobi R18N18G Traducción De Las Instrucciones Originales

Ocultar thumbs Ver también para R18N18G:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 14
m) Do not select contact actuation mode when working on
scaffolds, ladders or platforms where you may need to
move your body position. You may unintentionally fire a
nail by inadvertent activation of the workpiece contact
while moving about if the contact actuation mode is
selected. When moving positions, select full sequential
activation or deactivate the product completely by
removing the battery pack. This will reduce the potential
for injury to yourself and others.
DEPTH ADJUSTMENT SAFETY WARNINGS
a) Always remove the battery before adjusting the depth
of drive wheel.
b) Do not pull back on the adjustment wheel, the wheel is
designed to be rotated.
c) Do not press the trigger while adjusting the depth of
drive wheel.
d) Always select full sequential firing mode before
adjusting the depth of drive.
e) Do not point the tool towards yourself or anyone nearby
when adjusting the depth of drive.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
Damage to hearing
Note: Always wear effective hearing protection and limit
exposure to noise.
Injury to the eyes caused by incorrectly driven nails or
flying dust and debris.
Note: Always wear suitable eye protection.
Injury caused by vibration
Note: Hold the tool by designated handles and limit
exposure to vibration. See "Risk Reduction".
Lacerations caused by contact with sharp points.
Note: Take extra care when handling or loading nails.
The product is heavy.
Note: The product is heavy. Beware of muscle strain
when operating the product for extended periods,
especially if using overhead.
2
RISK REDUCTION
It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
numbness and blanching of the ngers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking, and work practices
are all thought to contribute to the development of these
symptoms. These are measures that can be taken by the
operator to possibly reduce the effects of vibration:
Keep your body warm in cold weather. When operating
the unit, wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
After each period of operation, exercise to increase
blood circulation.
Take frequent work breaks. Limit the amount of
exposure per day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor about
these symptoms.
WARNING
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.

KNOW YOUR PRODUCT

See page 91.
1. Firing mode selector
2. LED lights trigger
3. Operating handle
4. Air pressure adjustment knob
5. Nail depth adjustment wheel
6. Jam release lever
7. Workpiece contact actuator
8. Low nail indicator window
9. Magazine
10. Magazine slide latch
11. Firing actuation trigger
12. Belt clip
13. Battery port
MAINTENANCE
WARNING
The product should never be connected to a power supply
when you are assembling parts, making adjustments,
cleaning, performing maintenance, or when the product
is not in use. Disconnecting the product will prevent
accidental starting that could cause serious injury.
a) When servicing, use only identical replacement parts.
English

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido