Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Frame rail
Hitch Shown In Proper Position
Equipment Required: #2 Phillips Screwdriver
Fastener Kit: 75776F
Wrenches: 17mm, 19mm
Drill Bits: None
Plastic Push Pins
Figure 2
j
Qty. (4)
M12 x 1.75 x 120 Bolt CL8.8
k
1/2" Conical Washer
Qty. (8)
l
Qty. (4)
M12 x 1.75 Nut CL10
1. Lower and remove spare tire from vehicle. The tire release is located underneath the storage compartment in the back of the vehicle.
2. Remove the access door on rear fascia by removing the two plastic push pins with a #2 phillips screwdriver and pushing the two outside tabs
inward. (Figure 2)
3. Raise hitch into position and insert M12 bolts through the bracket and frame as shown in Figure 1. Note: The plastic bumper locator pin may
interfere with the hitch hardware. If necessary, trim the locator pin at the shoulder to allow proper hardware clearance.
4. Insert M10 bolts through bracket and into the frame as shown in Figure 1 (Hand tighten).
5. Torque M10 bolts first and then M12 bolts to the specifications below.
6. Reinstall spare tire and make sure it is seated properly.
7. Reinstall access door removed in Step 2
Tighten all M10 CL10.9 fasteners with torque wrench to 40 Lb.-Ft. (54 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2013 Cequent Performance Products, Inc.
Installation Instructions
Hyundai Santa Fe GLS/Limited
Fascia
Access Door
jkkl
(6/7 Passenger)
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
Fasteners typical both sides
2 Existing Weld Nuts
(Typical)
Figure 1
m
Qty. (4)
M10 x 1.25 x 30 Bolt CL10.9
n
7/16" Conical Washer
Qty. (4)
Tighten all M12 CL8.8 fasteners with torque wrench to 72 Lb.-Ft. (98 N*M)
Sheet 1 of 3
Part Numbers:
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
7000 Lb (3401 Kg)
5000 Lb (2267 Kg)
Accessory Rating
Not Shown for Clarity
mn
75776N
4/16/13
75776
44691
87637
Max Tongue
WT (LB)
750 Lb (340 Kg)
750 Lb (340 Kg)
C
Existing Sleeves
Rev. A
Form: F205 Rev C 9-17-2012

Publicidad

loading

Resumen de contenidos para Cequent Performance Products 75776

  • Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75776N 4/16/13 Rev. A 2013 Cequent Performance Products, Inc. Form: F205 Rev C 9-17-2012...
  • Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75776N 4/16/13 Rev. A 2013 Cequent Performance Products, Inc. Form: F205 Rev C 9-17-2012...
  • Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 75776N 4/16/13 Rev. A 2013 Cequent Performance Products, Inc. Form: F205 Rev C 9-17-2012...

Este manual también es adecuado para:

4469187637