Publicidad
Idiomas disponibles
Idiomas disponibles
Always wear SAFETY GLASSES
when installing hitch
Note: Fasteners typical
Scan for step by step
PHOTO installation
instruction or visit
http://www.cequentgro
up.com/qr-product.aspx
NOTE: THIS PRODUCT IS NOT
RECOMMENDED FOR USE
ON A 1/2 TON VEHICLE.
(Conical Washer)
Teeth side
against hitch
FOR 1993 AND OLDER MODELS
FOR 1993 AND OLDER MODELS
Remove strap from hitch, re-use washer and nuts for installation.
1.
Lower the spare tire for installation. It will be replaced later.
2.
Align the hitch under the truck so that the 1/2" hole in the side of the hitch bracket is directly below the slotted hole in the frame that the spare tire hanger was hooked into. Clamp the hitch in place
with the bolt plates between the frame and the hitch bracket. See the diagram above.
3.
Check to see that the reinforcing strap will bolt into the hitch bracket and the slotted frame hole. If it is not aligned, reposition the hitch so it will.
4.
Using the holes in the bracket as a guide, drill 1/2" holes into the frame at the forward mounting locations. Drill a 5/8" hole in the rear mounting locations.
5.
Insert 1/2" carriage bolts with square hole bolt plates down through the frame in the front holes. NOTE: Use the small bolt plates in the middle holes. Install 1/2" serrated washers, lock washers, and
nuts on the bolts. Insert 5/8" hex bolts with round hole bolt plates in the rear holes. Install 5/8" flat washers, lock washers and nuts on the bolts.
6.
Install the reinforcing strap with the 1/2" hardware as shown in the diagram.
7.
Tighten all ½" GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M) and all 5/8' GR5 fasteners with torque wrench to 115 Lb.-Ft. (156 N*M)
Proper torque is needed to keep the hitch secure to the vehicle when towing.
8.
Reinstall the spare tire. The "J" hook that was in the frame will need to be moved farther forward on the frame and relocated there. Relocate the spare tire as best suits your truck so as to clear the
hitch.
NOTE: To use the adapter bushing with some 2" weight distributing bars, it will be necessary to sand the corners of the bar to get it into the bushing.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or
ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©2016 Cequent™ Performance Products, Inc. -
Installation Instructions
PART NUMBERS: 45505, 45705,
CQT45505
both sides
⑦
⑬
⑤
④
⑫
⑤
④
⑬
Rear
Figure 2
⑧
⑨
⑩
Printed in Mexico
①
①
②
⑥
②
⑭
⑫
⑪
⑭
⑫
⑪
③
④
⑤
Sheet 4 of 12
Fastener Kit : 45505F
1
Qty. (4)
Carriage bolt ½-13 x 2.00 GR5
2
Qty. (6)
Spacer.250 x 1 .5 x 3
3
Qty. (4)
Conical washer ½''
4
Qty. (8)
Lock Washer ½"
5
Qty. (8)
Het Nut ½ -13 GR5
6
Qty. (2)
Spacer .250 x 1 x 2
7
Qty. (2)
Bolt Hex 5/8-11 x 2 GR5
8
Qty. (2)
Flat Washer 5/8
9
Qty. (2)
Lock Washer 5/8"
10
Qty. (2)
Het Nut 5/8-11 GR2
11
Qty. (4)
Bolt Hex ½-13 x 1.5 GR5
12
Qty. (6)
Flat Washer 1/2"
13
Qty. (4)
Spacer (round hole) .250 x1.5x3
14
Qty. (2)
Straps * Not in fastener kit
Attached to hitch for shipping
45505N
6-3-16
Rev. A
Publicidad
