Listening To Fm Radio; Phono Encoding; Aux In Jack & Encoding - lauson 01TT18 Manual De Instrucciones

LAUSON

LISTENING TO FM RADIO

FM RADIO TUNING
1)
PRESS FUNCTION BUTTON REPEATEDLY TO SELECT RADIO MODE, FM INDICATOR WILL BE LIGHT UP.
2)
TUNE TO THE REQUIRED STATION BY TURNING TUNING KNOB TO TUNE THE RADIO FREQUENCY,
3)
WHICH IS SHOWN ON THE DIAL SCALE.
SELECT DESIRED VOLUME BY TURNING VOLUME KNOB.
4)
THE RECEIVER HAS A BUILT-IN FM WIRE ANTENNA HANGING AT THE REAR CABINET. THIS WIRE
5)
SHOULD BE TOTALLY UNRAVELED AND EXTENDED FOR BEST RECEPTION.
PHONO & ENCODING
NOTED
:
REMOVE THE STYLUS PROTECTOR.
-
BE SURE THAT THE TONE ARM IS BEING DETACHED FROM THE TONE ARM REST
-
PRESS FUNCTION BUTTON REPEATEDLY TO SELECT PHONO MODE, PHONO INDICATOR WILL BE LIGHT
1)
ON.
SET THE SPEED SELECTOR TO THE PROPER POSITION DEPENDING ON THE RECORD TO BE PLAYED.
2)
PLACE THE RECORD ON THE PLATTER, USE THE 45 RPM ADAPTOR IF REQUIRED.
3)
PUSH THE LIFT LEVER UPWARD TO RAISE THE TONE ARM FROM THE ARM PARK, AND
4)
THEN SLOWLY MOVE IT TO THE RECORD SIDE. THE PLATTER WILL START TO ROTATE.
PUT DOWN THE LIFT LEVER TO DROP THE TONE ARM AND TOUCH THE RECORD
5)
GENTLY. PHONO PLAYING STARTS NOW.
PUSH THE LIFT LEVER UPWARD TO RAISE THE TONE ARM FROM THE ARM PARK, NOW PLATTER WILL
6)
STILL BE ROTATING BUT PHONO PLAYING WILL STOP. TO CONTINUE THE PLAYING, THE USER NEEDS TO
PUT DOWN THE LIFT LEVER.
AT THE END OF RECORD, THE PLATTER WILL AUTOMATICALLY STOP ROTATING. PUSH THE LIFT LEVER
7)
UPWARD TO RAISE THE TONE ARM AND MOVE IT TO THE ARM PARK, AND THEN PUT DOWN THE LIFT
LEVER.
TO STOP MANUALLY, LIFT THE TONE ARM FROM THE RECORD AND RETURN IT TO THE ARM PARK.
8)
REMARK: AS SOME KIND OF RECORD THE AUTO-STOP AREA WAS OUT OF THE UNIT SETTING, SO IT WILL
STOP BEFORE THE LAST TRACK FINISHES. IN THIS CASE, SELECT THE AUTO-STOP SWITCH TO " OFF
" POSITION, THEN IT WILL RUN TO THE END OF THE RECORD BUT WILL NOT STOP AUTOMATICALLY (TURN
OFF THE UNIT BY POWER BUTTON OR SWITCH BACK THE AUTO-STOP SWITCH TO " ON " POSITION TO
STOP THE PLATTER ROTATE). THEN PUT BACK THE TONE ARM TO THE ARM PARK.

PHONO ENCODING

BEFORE SWITCH ON THE UNIT, INSERT USB MEMORY DEVICE TO USB SLOT.
1)
PRESS STANDBY BUTTON TO SWITCH ON THE UNIT, THEN SELECT PHONO MODE.
2)
PRESS THE REC BUTTON, THEN PHONO INDICATOR WILL BE FLASHING.
3)
TO FINISH ENCODING, PRESS REC BUTTON AGAIN, THEN THE UNIT WILL SWITCH TO USB MODE AND
4)
PLAY THE PREVIOUS RECORED TRACK.
REMARK:
THE RECORDING SPEED IS 1:1 AND ACCORDING TO THE ACTUAL PLYING TIME OF THE PHONO
-
- THE RECORDING FORMAT IS PRESET AT – MP3 BIT RATE : 128 KBPS
- DO NOT PLUG OUT THE USB DEVICE DURING RECORDING.
AUX IN JACK & ENCODING
PRESS FUNCTION BUTTON TO SELECT AUX MODE, AUX INDICATOR WILL BE ON, THEN CONNECT THE
EXTERNAL AUDIO THROUGH THE AUX IN JACK.
TURNTABLE
4
EN