PROFLO PF5112NHEWH Instrucciones De Instalación

Installation Instructions
HET Toilet Bowl and Tank
with 1.28 Gallons per Flush
Tools Needed
A. Screwdriver G. Wax Seal
B. Wrench
H. Marker
C. Tape Measure I. Plugs
D. Level J. Screws
E. Drill K. Flexible Supply Line
F . Flange L. Gasket Adapter
Remove Old Toilet
1. Shut off water supply line to toilet. Flush toilet
and remove all water from the bowl and tank.
Use a sponge to absorb the water.
2. Disconnect the water supply from the tank.
3. Remove tank from bowl, use screwdriver and
adjustable wrench or socket wrench. Loosen
toilet bowl flange nuts under caps.
4. Remove old bowl by carefully lifting it off the
floor. Clean flange and plug drain with a rag to
prevent sewer gas from escaping.
Install New Toilet
Flange
Flange Bolts
1. If new installation, install a toilet flange into
waste line per flange instructions. Make sure
you have the correct rough in toilet.
2. Remove the rag from the drain. Install the
flange bolts into the flange.
Sealant
3. Turn the bowl upside down and place it on the
flattened carton box to prevent damage.
4. Install a wax ring evenly around the bowl
flange, (horn).
© 2014 Ferguson Enterprises, Inc. All Rights Reserved
A
B
A
B
A
B
5. Gently lower the bowl onto the flange making
sure the flange bolts protrude through the toilet
bolt openings.
6. Apply pressure evenly and rock the bowl from
side-to-side and front-to-back until it is firmly
on the floor.
A
7. Install the washers, nuts, and caps on the
flange bolts snug. Be careful not to over tighten
because the china may break.
Wax Ring
8. Install the tank-to-bowl-gasket, tank bolts with
washer if it is not already installed, and place
tank on bowl.
Distributed Exclusively by Ferguson and Wolseley Canada
G
H
G
H
C
C
K
K
D
D
H G
C
K
D
Rubber
Bolt
Gasket
Washer
Nut
F
F
I
I
J
J
E L
E L
F
I
J
E L
9. Snug and level the tank nuts using a socket
wrench and holding the truss head screw
r i f l m i y s n d i t e e h a t k n w h t i
CAUTION: DO NOT overtighten nuts more than
required for a snug fit. DO NOT spin bolts inside
tank with a screwdriver.
10. Connect the water supply to the ballcock. Only
hand tighten the supply line. DO NOT USE
CHANNEL LOCKS.
11. Turn on water, flush, and check for leaks.
Adjust ballcock to proper water line height as Adjustable rod
Mould 2001
noted on the flush valve tube.
float cup
Adjustments
Fill valve
body
Water level adjustment:
Adjustable rod
Triangle
Rotating adjustable rod
gasket
Mould 2001
float cup Rubber will adjust the height of
seal
float cup and change
Plastic seal
Fill valve
water level.
Hexagonal
body Filter
seal
Triangle
gasket
Rubber
seal
Plastic seal
Hexagonal
Filter
seal
DIFFICULTIES REASON
Water level
Fill valve
is too high
adjusted
or too low
incorrectly
Fill valve
Shut-off valve
can't fill
not fully open
Filter clogged
Float cup is
stuck by tank
wall
Leaking Hexagonal nut is
loose
a c s e r w d v i r . r e
SOLUTION
Adjust water
level
Open
shut-off valve
Remove and
clean filter
Free fill valve
from tank wall
Tighten
hexagonal nut
22485 0914