Operation; Transport; Storage; Care And Service - Kärcher LMO 36-40 Battery Manual De Instrucciones

Operation

General information on handling the
lawnmower
The run time of the battery depends on several factors:
 The condition, length and density of the grass
 The cutting height setting
The maximum surface performance, depending on the
state of the grass, with a 5 Ah battery pack:
2
approx. 550 m .
The results of the mowing process can be optimised as
follows:
 Cut at a maximum of one third of the grass height.
 Reduce the speed at which push the device when
mowing tall grass.
Note
Do not mow wet grass. Wet grass sticks to the under-
side of the lawnmower and prevents correct collection of
the grass in the grass catcher or ejection of the grass.
Mowing lawns
WARNING
Lifting or tipping the lawnmower during operation
Incision injuries
The blade of the lawnmower rotates approximately par-
allel to the ground over which it moves. Take care to en-
sure that all four wheels touch the ground when
mowing.
1. Install the grass catcher or mulch plug (see Chapter
Initial startup).
2. Set the cutting height using the cutting height adjust-
ment lever.
Illustration I
Choose the cutting height according to the condi-
tion, length and density of the grass (see Chapter
General information on handling the lawnmower).
Illustration J
3. Press the start button and the ON/OFF switch.
Illustration K
The device starts.
4. Release the start button and hold the ON/OFF but-
ton pressed.
Empty the grass catcher regularly when using the grass
catcher, otherwise the ejection chute can become
clogged with cut grass (see Chapter Emptying the
grass catcher).
Mowing edges
Lawn edges, e.g. along a wall, can also be mown using
the device.
1. Push the lawnmower along the wall, close to the
wall.
Illustration L
The side inlet ensures that the grass is pulled into the
cutting zone.
Illustration M
Finishing operation
1. Release the ON/OFF switch.
Illustration N
The motor stops.
Removing the battery pack
1. Open the battery flap.
Illustration O
2. Remove the safety key.
3. Press the battery pack release.
4. Remove the battery pack.
5. Close the battery flap.
Emptying the grass catcher
The flap on the grass catcher filling lever indicator clos-
es when the grass catcher is full. Empty the grass catch-
er in this case.
1. Lift the ejection chute flap.
Illustration P
2. Remove the grass catcher.
Take care to ensure that the motor control cable re-
mains in the cable holder when removing the grass
catcher.
3. Empty the grass catcher.
WARNING
Sharp blade
Incision injuries
Be careful when tipping or lifting the device.
Keep all parts of your body away from the cutting blade.
1. Switch the device off (see Chapter Finishing opera-
tion).
2. Ensure that the blade is no longer rotating.
3. Allow the device to cool down.
4. Remove the safety key (see Chapter Removing the
battery pack).
5. Remove the battery pack.
6. Secure the device against slipping and tipping over
when transporting in vehicles.
Clean the device before storing (see Chapter Cleaning
the device).
1. Remove the safety key.
2. Remove the battery pack (see Chapter Removing
the battery pack).
3. Unlock the handle locks.
Illustration Q
4. Push the telescopic handle in completely.
5. Lock the handle locks.
6. Release the quick-release catch and fold down the
handle.
Illustration R
7. Place the grass catcher on the handle and the de-
vice.
Illustration S
8. Store the device in a dry, well ventilated location.
Keep away from corrosive substances such as gar-
den chemicals and defrosting salt. Do not store the
device outdoors.

Care and service

WARNING
Sharp blade
Incision injuries
Be careful when tipping or lifting the device.
Keep all parts of your body away from the cutting blade.
Cleaning the device
1. Remove the safety key.
2. Remove the battery pack (see Chapter Removing
the battery pack).
3. Clean the exterior of the device with a soft, damp
cloth or brush each time after use.
Illustration T
Clean the blade before longer storage periods.
4. Tip the device onto the side.
Illustration U
English

Transport

Storage

21