Park Tool THS-1 Manual De Instrucciones

PARK TOOL CO.
5115 Hadley Ave. N., St. Paul, MN 55128 (USA) www.parktool.com
THS-1 Backplate Sub-Assembly
1. Place carriage bolts through the square holes
with the arms aligned to the mounting holes
on the backplate.
2. Once both arms are in place with the carriage
bolts showing, place the mount plate horizon-
tally along the top two and bottom two car-
riage bolts as shown (Figure 1).
3. Hand tighten the four lock nuts to retain the
arms onto the back plate.
4. Align the arms parallel. Once aligned, torque
the carriage bolt nuts to 20 ft-lbs (27 Nm).
5. Install grips onto arm ends, keeping logo text
horizontal. Optional: utilize an aerosol hair
spray or other spray adhesive to aid assembly
and retain grip permanently.
THS-1 Mounting to a Permanent Structure
1. Complete Backplate Sub-Assembly prior to
mounting to vertical surface.
2. Align the four outer-most mounting holes on the
THS-1 backplate sub-assembly with the desired
position on the flat wall. If mounting to post, use
the center two holes. Utilize backplate as a tem-
plate to mark holes for any drilling.
3. It is recommended to place the bottom mount-
ing holes 54" above the ground. Additional-
ly, ensure adequate space surrounding the
stand is available to clear a bicycle mounted
in the stand.
1
2
THS-1 & THP-1
THS-1 Trailhead Workstation and THP-1 Mounting Post
4. Utilize four ½" (13mm) diameter concrete an-
chor studs (or similar fastener for other mate-
rials) to mount to a concrete wall (Figure 2). If
mounting to post, use two fasteners in center
two holes. Fasteners not included. Follow fas-
tener manufacturer recommendations for hole
sizing, drilling, and applied torque.
THP-1 Mounting to Ground
1. The THP-1 has been designed to be mount-
ed to the Park Tool #130 baseplate or to a con-
crete surface.
Direct Mount: Utilize four ½" (13mm) diame-
ter concrete anchor studs (or similar fasten-
er for other materials) to mount to surface
(Figure 3). Follow fastener manufacturer
recommendations for hole sizing, drilling,
and applied torque. Fasteners not included.
#130 Baseplate: Utilize four ¼-20 fasteners
to assemble the THP-1 to the Park Tool #130
baseplate (Figure 4). Fasteners not included.
2. Ensure top tube square cap is pressed in securely.
THP-1 Post Protector
1. Vertically align the tall side of the film with
the forward face of the THP-1. Center the film
on the post, 2" above the baseplate and press
onto the post. Start with the forward face and
apply pressure outwards, wrapping the sides
around the post and working air out from the
center to the edges (Figure 5).
Instructions / Instructions / Anleitung / Instrucciones
THS-1 Mounting to the THP-1
1. Complete Backplate Sub-Assembly prior to
2. Align the middle two vertical mounting holes
3. Once positioned correctly and hand tightened,
4. Ensure top tube square cap is pressed in securely.
THS-1 Tools and Cover Assembly
1. Place tool cable into slotted backplate tab in
2. Hinge front cover by aligning and placing the
3. Align the three holes, one on each side, and
4. Check to ensure all cables are situated in their
3
4
mounting to the THP-1.
on the THS-1 backplate sub-assembly with the
smaller two holes on the THP-1 post. Place the
socket head cap screw from the back of the post
into the hole. Hand tighten the nut onto the back-
plate. Repeat for the lower fastener (Figure 6).
torque the nuts to 50 ft-lbs (68 Nm).
locations desired for each tool (Figure 7). There
should be four on each side of the arms. The
cable stop should sit on top of the slotted tab.
top two back cover tabs into the respective
slots on the front cover and rotating the base
of the cover down (Figure 8). Ensure cables re-
main in each slot.
one centered on the bottom of the front cov-
er, and hand tighten all three tamper proof fas-
teners. Once all three are hand tightened, use
supplied TR27 tool to tighten fasteners. Keep
tool in safe place for future use.
slot and none are pinched.